few more things,
the frame bottom and especially the kickstand bracket are quite close to the ground and so I'm afraid on street turns to turn too tight in case it would catch/slide on the ground and cause the bike to buck crazy. In woods with softer ground it's not much an issues unless...
I'm not sure the exact clamps but there's some that are meant for dirtbikes/motorcycles that are specifically meant to not split and they're like $100+. Actually, they might be the $80 gorilla grabber ones, I haven't researched much into the aftermarket ones yet.
Best would be male teeth on...
I'm replacing the clamps with a much better motorcycle/dirt bike kind which is said to be the most secure, costs like $180 or something but I don't care. If I can retro fit these even if have to drill new holes will be fine, the frame is strong there.
It's common even for motorcycles the bars...
I asked reddit firefighters. They suggested a mini foldable shovel which seems to be the best choice, where I ride the dirt should be pretty easy to dig. I was considering the Element mini one they're like $90 looks like a flair but reviews show they are basically useless, even the spray paint...
go this from gopowersports for around $1200. UPS DESTROYED the box but it's like 150 lbs stuffed into a single-wall cardboard box no reinforcements. UPS guy said something like I can't check through it and then decide to send it back or not, so I signed for it knowing GPS would replace anything...
I have a 212 tillotson stage 1 mini bike with single coil, it doesn't have a battery. I'm going to wire the LED headlight to the single coil. Is there a way to wire a loud horn? There's motorcycle horns on ebay says 115dB but there's little dinky ones running on small button batteries that claim...
I'm referring to these
https://www.gopowersports.com/7-8-handlebar-riser-clamp-kit/?campaignid=15940148387&adgroupid=&adid=&gclid=EAIaIQobChMImZGZhs7c_QIVofzjBx2KYQAREAQYBiABEgLUv_D_BwE
BTW, only one half is threaded which it doesn't show the threads in the photos, or neither is threaded and...
I have this type of exposed ribbed cylindrical air filter on my tillotson 212 stage 1 kits mega moto 212 mini bike. It came with the mesh type sock/cover shown in photo. I think I say in some youtube video or something that either cloth or mesh is better for muddy/rainy/dusty conditions but that...
just assembled a mega moto 212 tillitson from GPS. I tightened the 2 U-clamps that squeeze the handle bar really well using an allen key and tapping it with a hammer instead of twisting with the hand, seems I got them as tight as possible but the handlebars slips a little forward/back, like when...
mega moto 212 is a nice bike. But I tightened with the wrath of god on the U-clamps which secure the handlebar to the frame but they still move around I think I have to drill, tap threads and put a bolt down in each in the spot I like them, because I ride woods /trails and don't want it moving...
Well I've decided to keep the stock plain short bolt, because I ride woods and sometimes have to go over stumps branches etc that can be sticking up and don't want anything breaking an extension and have all the oil pour out. I've also ran the rear brake cable on the top of the frame too instead...
Turns out I can run an LED bulb with the single-coil my engine already has. Would need dual coil to run the non-LED stock bulb this bike came with, because LED needs less energy I guess.
In the youtube video above GPS linked the motorcycle bulb they found can be swapped with the stock bulb.
I...
Hi I'm finishing building my Tillotson 212 e-start stage 1 on a mega moto 212 frame. It came with a non-LED headlight but I didn't even bother installing it because I think I need a brighter LED, and will sell the non-LED on eBay as new.
The kit didn't come with a battery but there's terminal...
Hi, I have a tillotson 212 E-start on an mega moto 212 frame. I wanna add an extension to make draining oil cleaner + easier, EDIT, I just checked before mounting the engine it seems the front OEM plug will hang over the frame for an easy clean draining but while I'm making the thread I figure...
^ correct, thanks, and yes I was thinking might have to prop something like the flywheel but I got it off.
It's 5/16-24 FINE thread, NOT 5/16-18 more common in store bins.
I was able to get the stock bolt out with a giant channel lock with rubber sheet wrapped around the shaft and a breaker...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.