Search results

  1. S

    Tillotson Carb gas to methanol help!

    It can be done, but I think I would just find a Tillotson that was designed for alcohol. If you are determined to do it, ask on one of the Go Kart Facebook groups, like VKA. https://www.facebook.com/groups/1394603367499268
  2. S

    Need Help, Engine Seized/pull cord stuck.

    Make sure the recoil isn't the problem. Sometimes they jam and nothing turns. You might get lucky!
  3. S

    Clinton A400 Rebuild

    If you are not getting my private messages, text me at 678.617.0730
  4. S

    Clinton A400 Rebuild

    I'll message my paypal address.
  5. S

    Clinton A400 Rebuild

    The 83-12-500 flywheel is CCW. it is the one in upper left above - $25 The linkage kit is $25. The better rod is $50 if shipped in the same box Shipping for above - $18
  6. S

    Clinton A400 Rebuild

    Yeah, it is a lefty, which is correct for your kart. Then the upper left flywheel will work. Is the engine in decent shape? Rope start engines typically are pretty old.
  7. S

    Clinton A400 Rebuild

    83-66-500 flywheel is for a reverse rotation engine ( clockwise rotation viewed looking at the PTO). That was an option for karts that need a an engine on the right rear of the kart, before 'live axles' were available. So the kart you are working on will dictate the engine position and rotation...
  8. S

    Clinton A400 Rebuild

    I checked and I do have some aluminum flywheels
  9. S

    Clinton A400 Rebuild

    A picture of the LMB70 would help. Throttle linkage for those Clintons is tricky once you remove the governor. It doesn't get any easier with a Tillotson, as the fan housing will get in the way of the mixture needles or the linkage. A Go Power manifold helps, but they are pricey. I have Clinton...
  10. S

    Clinton A400 Rebuild

    I'm confused! :) PM sent with paypal address
  11. S

    terryas@att.net is my paypal

    terryas@att.net is my paypal
  12. S

    Clinton A400 Rebuild

    I have a few rods left. $60 shipped in the US - USPS flat rate small box terryas@att.net
  13. S

    Clinton A400 Rebuild

    The muffler SPARKWIZARD mentioned is a good cheap option. I usually either drill holes in the end or completely cut the end off for maximum flow. The E65 factory megaphone does not fit on an A400. There is a knock-off that fits both engines, but very hard to find. Yes, the factory sold a gokart...
  14. S

    1960 Percival Hellcat

    Gaskets are available for the carb. Measure the float bowl diameter and i can tell/send you what you need.
  15. S

    Wanted: Clinton #46-674 (403171) Crankshaft

    That is a left hand E65 crank. Looks fairly decent. Why do you want to replace it? I have most parts to get your E65 going. HIt me at terryas@att.net
  16. S

    Clinton A490 Panther

    I have a used coil with the same number, 5733, on it. I get similar Ohm readings. Yours if you pay shipping. Priority small box is 10.40 I believe. Throw a new set of points at it.
  17. S

    Clinton A490 Panther

    Ok, I’ll see what I come up with
  18. S

    Clinton A490 Panther

    I’ll look tomorrow and I’ll see if I can check ohms resistance on one. Hard to diagnose
  19. S

    Clinton A490 Panther

    Show me what you have
  20. S

    Clinton A490 Panther

    Go to ebay and search for: Timken - 470601 That will get you to a seller that has everything you need. 471646 is for the A400 PTO 470601 is for the A490 PTO 254270 is for both bearing plates
Top