Search results

  1. C

    Anyonw ever buy from this vendor?

    Looking for feedback here, does this look legit? https://www.spindlesshop.com
  2. C

    Son wore them out. Tire recommendation needed for 5.30/4.50-6

    Bummer those would be ideal in right size
  3. C

    Son wore them out. Tire recommendation needed for 5.30/4.50-6

    Great. Thanks for the feed back
  4. C

    Son wore them out. Tire recommendation needed for 5.30/4.50-6

    My son finally wore out (side split) the vintage 1969 "General" brand tires on my Fox Trailbug. I'd say between the original owner, myself in the 70's and 80's and my son, they owe me nothing. I will probably remove them, clean them up and hang them up in the garage as a keepsake. So for new...
  5. C

    HS 40 throttle arm disconnected

    I will try that and report back. Thank you sir
  6. C

    HS 40 throttle arm disconnected

    Rev limiter arm came off, shaft moves in and out an 1/8" so that when I try to press the arm back on it is not long enough. Is the arm just a press fit against the shaft? See pics Cheers
  7. C

    HS40 Throttle linkage works only when engine is OFF?

    opps sorry :)
  8. C

    HS40 Throttle linkage works only when engine is OFF?

    And we have lift off! Runs great! Thanks fellas!
  9. C

    HS40 Throttle linkage works only when engine is OFF?

    Ah, ha, I'll give that a shot....
  10. C

    HS40 Throttle linkage works only when engine is OFF?

    Hello, Set up a new tecumseh throttle on my HS40 snowblower engine circa 1970. The set up works flawlessly until I start the engine, then the butter fly moves a hair and no more. Turn engine off and it will work again perfectly. At my wits end. Please help as my son really wants to ride my...
  11. C

    Battery powered headlight/tailight recommendations.

    Looking for recommendations for headlight and tailight, battery powered AA or AAA batteries or rechargable. Vintage look a plus but not required
  12. C

    Recommendation on Kill switches from Amazon

    I actually wired it backwards on purpose. I want my son to have a bigger target button to push in a jiffy. Works great!
  13. C

    Recommendation on Kill switches from Amazon

    Thanks both switches seem the same, bought the kit for a spare cable. Thanks guys
  14. C

    Recommendation on Kill switches from Amazon

    So many to pick from, can anyone recommend one or what to avoid?
  15. C

    HS50 No spark after new points and condenser? Test coil?

    "If that OG crimp washer that the C/C wires go to is touching the stator body in any way they will ground out. I would remove the wires, tighten the post down (it has to be tight to get the right points setting and operate correctly) recheck for .020" Markus you truly are worthy of your...
  16. C

    HS50 No spark after new points and condenser? Test coil?

    Took better pics for your "Obi One" feedback Markus. Thank you. The coil wire is grounded to the condenser mount (towards back side)
  17. C

    HS50 No spark after new points and condenser? Test coil?

    OK thank you. Shopping for new coil now...
  18. C

    HS50 No spark after new points and condenser? Test coil?

    Yikes, that's too bad. I assume that would mean I'd have to set the timing again. That would be my first redo.
  19. C

    HS50 No spark after new points and condenser? Test coil?

    Re glued steel flywheel magnets and installed new points (OEM) and condensor in hopes of curing no spark issue. How can I test the coil to rule that out?
  20. C

    Flywheel magnet spacing on steel flywheel?

    Thank you very much. Not sure how important the spacing is but why just guesstimate? Generous offer on the flywheel. If the JB Weld does not hold, I'll take you up on it. Cheers!
Top