Search results

WANTED RUPP clutch drum and sprocket 11 tooth, #35 chain, part # 13917 for my 1970 Chopper project.

Looking for information, wiring diagram or parts catalog or where to get ignition parts for the "1972 only year" BSE engine model # ECO9M-A. I have a no spark condition and have clean points and a good condenser. Flywheel magnets are very strong. Might be the coil or magneto ? Has great...

I am looking for info on a MOTO-SKEETER 650 minibike. It has the BSE 650 2 cycle engine in it and has intermittent spark. Spark plug and points are good, I suspect a bad condenser or coil. Anyone have an idea where to find these parts or what other engine may have the same ignition parts ? It is...

CLUTCH COVER for Gilson, Montgomery Wards, Allis Chalmers mini bikes. Never mounted, but has some small rust spots due to poor storage. $350.00 + $29.00 shipping and insurance. Oak Grove, MN

BONANZA CHOPPER SEAT COVERS are back in stock at BlackWidowmotorsports.net Oak Grove, Mn $100.00 each + shipping http://blackwidowmotorsports.net/_b50001_bonanza_mini_chopper_seat_cover.html

Looking for info on whether the Rupp made minibikes Sears sold had a Rupp ID- serial number tag on them or if they had a Sears ID tag ? Specifically on the Rupp Continental models that I have seen in Sears catalogs back in the mid sixties. Please share any knowledge or pics if you have one...

New Speedway fenders are now available. $135.00 each plus shipping. At blackwidowmotorsports.net in Oak Grove, MN

1970 to 1976 Rupp front and rear fenders 20” and 12”. $135 to $130 each plus Shipping.

Does anyone have any info on Robert Stanton at RobRon ? Trying to contact him about some parts. Is he still around ? Thanks, Jim

I need a rear swing arm for my Speedway with 14" wheels. Let me know if you have one. Mine is bent.

Looking for rebuild parts for a Sachs 80B engine. I.E. standard rings, jug gasket, point cam, flywheel key and nut. Thanks

Does anyone know what brand or size belts these would be? They are cog tooth torque converter belts. The numbers on the belts are: SED 99-70, SED 99-75, SED 99-80 They appear to be a 5/8" width belt. Thanks for any help.

I have a new 10" WHEEL - 20 SPOKE with brake drum hub. 3-1/2" across the drum opening. $120.00 shipped from MN

Nice roller.Great starter kit for a restorantion. What you see is what there is. $500 firm. Located north of Minneapolis. Buyer pays shipping via UPS

Nice little bike,All original and popped right off on a shot of ether. Tank is clean looking although I would recommend a flush. Correct 3hp engine. Missing clutch cover. Bike is disassembled and boxed for shipping. Shipping will be via UPS at buyers expense. Located near St.Francis,MN just...

Want to buy a Speedway TC Drive and Driven clutch assembly for my Red Baron project. Also any related or extra parts you may have.

I had a few people ask about wiring on the 1968 Rupps so I finally drew up a wiring diagram.

https://minneapolis.craigslist.org/wsh/mpo/d/pepin-rupp-scrambler-for-parts-or-repair/7305970866.html Left in a field upside down?

Saw this on Craigslist https://minneapolis.craigslist.org/ank/snw/d/stacy-1971-rupp-blackwidow/7075377314.html

Anyone know of a master model number list of the Tecumseh engines used by the minibike makers? Or can anyone post what they know? Example HS40-55415C it's a lighting coil model, long shaft, with slanted intake. Thanks