Search results

Thanks very much:smile::thumbsup:

B&S Intek 206 6.5hp VALVE SETTINGS ??????????? have dial-up so cant watch vidios, does this model have adjustment, i didn't remove valve cover yet awaiting info? anyone know the exh. & int. clearence, i assume adjusted cold? i couldn't find instructions on this anywhere i looked? I think its...

Thats not good. Has Don tried giving info to Highway Patrol, they have cams in cars and maybe cal trans cams? Sucks....Keep trying and might get lucky.

Error, delete Got answer on B&D threads where i should have posted 1st....

Yeah it hurts and especially if they were dumped for scrap metal, check those places also like in sunland. So its to late now but Was there a trailer hitch lock installed? Was there a GPS locater on board, people use that type thing on bikes even? I would have had at least an alarm motion...

Is there a way to know the year built by ser no. ? Ihave a 3.5hp GX-110, sn.1711520, or is there something else to look for? :smile:

Couldn't find a breakdown, kept getting 'sorry' , might be me or too old a motor?:sad: b&s intek 206 6.5hp mod. 120412 0143 e1 / yr. 2002

Just got this intek 206 2 days ago and runs great but noticed some small pieces of old grass and bits of something I feel should come out. I tried to look inside with a light but cant see much, no visable sceen? I hope theres not more junk in the carb. So is there a screen or filter and where. I...

Just got this intek 206 2 days ago and runs great but noticed some small pieces of old grass and bits of something I feel should come out. I tried to look inside with a light but cant see much, no visable sceen? I hope theres not more junk in the carb. So is there a screen or filter and where. I...

You're not the only one. How many times ya gotta ask? is cam dead:out::shrug:

I'm not sure but think i have an old Clinton outboard motor, 5hp? Any motor in the hands of kids will take a dump at some point:wink: Cant get to my red clinton or would post a pic.... :drinkup:

Thanks, So if I get the later muffler guess i'll need the later gasket or does any combination not matter? At least I know now I have an antique:crying:

That sucks, guess i got lucky or who knows when mine gets up to operating temp might be another story? Gotta change the oil and air filter often but some people learn too late? The 6.5hp b&S not going to be used much, its for a water pump or log splitter, oil change and ready to mount...

Was looking on ebay for a stock muffler for the GX-110 I have. sn. 1711520. Mine has a round hole between the two studs but the gaskets shown on ebay are half round with a straight side, strange? Not going to pay those prices anyway but wondering if there was an early and late gx110? Should any...

Very nice breather u made, just like a custom one for a VW. I searched and for my model; 120412 0143 E1 it does have a cylinder liner but no ball bearings on crank which is ok. The shop thought it was a 3/4" shaft and straight unlike generator type thats tappered. Also mine is a 2002 year...

Thanks JK You noticed:thumbsup: thanks for the tip turning off the gas, just did... ""gatorade bottle strapped to the frame"" Very nice Fancy breather;-) I wasn't thinking these motors have paper filters, (now i understand why the PO said they changed the air filter not long before storing...

Thanks guys, picked it up tonight. I offered $35 and said no, i'l take $45 and i said how about $40, he said no but took $42 and the $2 i had was a two dallar bill LOL. Ran it and stared on second or third pull after putting 12oz of gas i took along. It sounded good running but WHAT! Plastic CAM...

He wants $50 in ad for motor alone with bad pump only attached? Was thinking to offer $40 if its ok, maybe $35 if looks ratty? Guess i'll start at $35 anyway, cant hurt;-) Thanks... PS. Thing is theres no way to feel compression by pulling the cord, Right? Think i'll take some gas along.

Found this 6.5hp intek to purchase but has the pressure pump still attached. Anyone know if its more likely to be a straight shaft. Think a couple models were tappered. guy said its a 206cc 121400 ?

Nice link;-) Interesting, i didn't think there was anything on Clintons... I had a 2-cycle panther i guess it is, gold color from a surplus store brand new for 29.95 in '60 i think. Put it in a mini bike scooter i built in jr.hi shop class. Put a rod threw the case over reving down a hill...