Search results

Vintage 1959 "Lets Go Karting" magazine. 20. shipped Taco Parking sign. 20. shipped LiL Indian chrome sticker . 13 shipped FantomResto@hotmail.com

Small gas tank, 8" X 3", clean inside, no dings. Cap neck threads are mangled as shown in pic, but the cap will thread on. With brackets. 35. shipped FantomResto@hotmail.com 602 705-6557

I have a Tecumseh 3 hp engine which I purchased new about 2 years ago, it has less than 1 hour of run time on it. It has been garage stored ever since. It is like new, but will probably need carb flushed from sitting. Ran perfect, but had very little use. It includes an upgraded air filter...

Complete Rupp Continental mini bike. 3 hp Tecumseh, not running due to sitting a while. Nice seat. Original turbines. Frame and wheels are repainted incorrect. 550. plus shipping. ( from Phoenix ) FantomResto@hotmail.com

Early Taco 22 frame with fork, scrub brake, some hardware. Also included is the new, undrilled seat. Frame does have some re-weld / damage repair, over-all is nice, straight, ready for resto. 250. shipped FantomResto@hotmail.com

Red metalflake and satin black 2-tone seat. 15" x 8". New, never mounted. 50. plus postage FantomResto@hotmail.com

A pair of vintage Rupp turbine wheels, front and rear, 6 inch. 70. shipped ***SOLD*** FantomResto@hotmail.com

J.C. Agajanian mini bike roller project. Original 6" mag wheels with sprocket. Frame has fresh windex - blue powdercoat. New seat. Includes original shocks (front & rear), Includes misc original hardware, pegs, etc. Original "Aggie" metalic decal is still present and in OK condition...

A couple pics of my Aggie project...Still have a ways to go, need lots of detailing and set-up.

Has anyone seen this yet ? Taco Mini Bikes - The Ultimate Mini Bike of the 1960's is back Opinions ? :drinkup:

2 Frames with forks. One is a Bonanza ( my loss is your gain, the engine plate has been modified for a large diameter jack-shaft gear ). Other frame is ok, but fork slightly bent. 50. each plus postage. FantomResto@hotmail.com

J.C. Agajanian Roller. Fresh candy metalic blue powder coat. NEW 2-tone large seat. Original straight frame and fork, magnesium 6 inch wheels. Foil "AGGIE" decal is still presentable. Has original jack-shaft set-up and sprocket. Lower section needs to be detailed. A heavy duty bike...

I hate to do it, but I need to let some stuff go. I just got this frame back from the powder coater, it is FRESH metalic candy red. Brand new seat from Ken. With a pair of Go-Power wheels ( 6 inch ). Tires and throttle are nice used parts. Also have the original fold-up pegs, not shown in...

I've had this bright red metalflake helmet on the shelf for years. No major damage or scratches, old decal / glue residue will clean up. Missing one snap on front, should be an ez fix. Size is about a medium. 30. shipped US Postal M.O. FantomResto@hotmail.com

Taco chain guard with small logo, as cast. 50. shipped Used 12 inch seat, small tears on bottom. 12. shipped A pair of 5 inch tubes, NEW. 15. shipped Tecumseh slanted carb adaptor, 1 7/8ths" between mounting holes. 20. shipped FantomResto@hotmail.com

Has anyone ever heard of these ?

I've got this Taco about 80% done now, just needs some small parts and fine-tuning. I decided to not go the resto route on it, using a Tecumseh for power, 6 inch Astros, and it isn't purple ! Thought I'd share pics... 2nd pic shows the rear slick and cylinder gas tank I added...

Speedway Shrike roller project. Frame has been bead blasted, epoxy primed, then lightly covered with spray can candy turquoise. Tank is straight and fairly clean. Front fork is Rupp. Original 10" chrome wheels have some peppering, with original Carlisle knobbies. Handle bars are rider...

I'm looking for info on where I can get a clutch band-brake setup. I see that the Allied Leisure catalog has the entire kit for about 60. , but I have heard some not-so good things about this company. Does anyone have just the mounting brackets for these types of brakes ? Any info would be...

Hello... I am looking for a 20 degree offset intake for a Tecumseh 3 hp. Rupps and Speedways with a 20 degree angled engine-mount use these . Any help is appreciated . Thanks. FantomResto@hotmail.com