Search results

thanx hause for the post!!!

Chopper mini bike(set up like a drag bike(strait bars) This is a nice mini with a nasty look of a drag bike. 7hp, robyn Subaru ex 21 runs excellent..Plus looks spark perfect! This is a Superior engine!!! Commercial grade motor… Runs excellent.. The engine has never been altered...

Ordered a Gecker magnum machined blue printed shoe clutch,from Sheldon @ Gecker motor sports for my kart..this clutch drum and sprocket are both machined..this should be a kicker,it locks out @3700rpmm..will be here on monday...can't wait...

I have a Mikuni VM22-133 Round Slide Carburetor 22mm Carb.it is the more expensive one.I ordered pilot jets for AKG,and the OG pilot jet is shorter than the one I just bought??I got some main jets to from them the to were diff.the OG were a 8mm bolt type and the new ones are srcew in type..but...

got it fired up,fuel pump needed tcl,little tweakin and it sounds killer..got change some jets to 2 play with 115 & 125 mains and a 17.5 pilot jet,and a shcem of the power curv...and some luck... just got it ready,for a first test run in 2000 jag.cart.. bt im not gonna the motor is scary...

thanx nova,that spot did it...gets tricky I had to remove the sub plate on the cover,and grind inside a bit so to clear the brass nipple..works awesome,running to rich!!gotta.check valves ?maybe use a guage this time!! thanx!! to all

need to drill hole for the brass pulse nipple,on the 5 hole clone valve cover.. it looks like the best spot is right in the middle of the "o" in the lettering,(there is nothing behind that area to interfear... anyone agree?disagree?

This fella hooked me up with a replacement 5 hole valve cover,and a set of stock rockers that I was in dier need of for only cost of shipping!!!.... not to mention he does not even know me.... or he probably would not have!!!HA! what a guy....thanx again JF

looking for my del.to R.I."valve cover and rockers"not sure now who it was? let me know if you see this post!did u get the check? thanx JF

clutches I know this was not one of your picks,but I have read a lot bout the "Gecker magnum" blueprinted clutch for $99.00 it locks out at 3700 rpm..what is your thoughts on that one.. a clutch is the last item, needed on my kart to test run it it's need a 18 month project... was...

no,I did have the header on it.But I installed a muffler system,to keep her quiet..My boy has an awesome spot to ride.My sister lives on a dead end.And don't wanna piss anyone off. this is my build below fo rmy kart...only bout 1/2 way there.. hillbilly header vs 22mm slide...

I have a bone stock clone on my kids race kart (just for playing)I am leaving it that way,but was thinking that I could change the carb jet,and the em.tube,and air filter for a bit more spunk...and not much cost..the govenor is staying it's our friend!!! would it be a good thing if I put in...

all set just got one.....

lookn for a used shoe clutch max T or noram? in decent shape,higher tooth the better over 15 if I can find one? if not will settle for lower tooth....just need something to get my kart rolling to test my build...going to get the "gecker machined magnum" when I can swing it.... let me know if...

really??? ok,send me your address,and ship cost.. via PM can I send personel check today,Ill wait for the check to clear with you,saves a trip to get money order..If thats ok with you??

nice!!!!!!!

looking for input on this clone combination engine is for play kart!! new clone w/existing parts 22 mm carb open header billet fly wheel arc rod new wrist pin and c clips will the following mods make sense and work well 1.2 rockers w/laser cut giude plate 18# springs?? or do I...

I have a new greyhound,and is has the following: vs 22mm slide carb govenor,ect removed open pipe my plan is to make the following in the next few weeks.. 1.2 rockers and laser cut guide plate 18# springs advance timming 4 deg. THEN WILL add the follwing set up: arc rod,mild...