14cc

***FOR SALE*** New Hi-Compression 14cc honda clone head with valve guides installed and valve seats installed and cut. will fit stock honda and predator valves (per ARC). but ready for you to take it up to whatever notch you want. with the head, new dual spring kit (green stripe), new guide...

Old style gx160 head(27mm/24mm) Going to port it and mill it prob .065 or more depending on clearance Flat top piston file fit rings Stock bore Arc +.020 con rod NrRacing 307-1006 cam CM pushrods 1.3 billet rockers Dual springs Arc billet aluminum flywheel 6619 (8* advance) On 110octane...

Genuine honda 14cc head with rockers, valves. Asking $70 obo Shipping $12 via usps to lower 48 from baltimore, Md.

I put a valve stem through the head of my GX160 and need a new. I would prefer a Honda but will settle for a clone. I can buy one off ebay and nr-racing for $40 so I was looking to spend around that price, I will spend more for a Honda though. I figured I would look here cause I would rather...

located at 10509 . $50 Obo plus shipping. all honda hardware except rockers. this will increase compression and it is a honda.

Started raining 160's again here. $50 obo plus shipping from 10509. Comes with all hardware. Its in great shape but dirty. Valves and seats show no wear. With a little love it can look like this one. I just don't have the time.

I need a 196cc clone carb looking to pay 10 for the carb plus shipping. I also need a 14cc head or two looking to pay 20 plus shipping for each. Let me know if you have one and how much you are asking please.

I have a brand new 14cc clone head and a 18cc that has been ported and polished and milled .70. Which would be better to use for a racing setup. The other engine mods are: billet flywheel and rod 22mm mikuni carb 8* timing key black mamba cam cromo push rods champian rockers billet...

Looking for 14cc cylinder head with 26lb springs retainers, ss valves porting would be nice too

Nice shape. Was gonna use it on my bike, but decided to keep the motor somewhat stock. Came off a running GX160. Looking for $30 plus shipping. Probably fit in a flat rate box. Let me know if you have any questions. Thanks.

would there be a problem if i put a 14cc head on a modified predator without the dowel pins and if i torqued down the cylinder bolts to 17-18 ft of torque?

Selling this, I will post internationally. Check out this item I found on eBay: End time: Dec 8, 2012 9:35:39 PM Item: Honda Gx160 or gx200 6.5 5.5hp high compression cylinder head or stock 14cc URL: http://pages.ebay.com/link/?nav=item.view&id=221159974715 Alt URL: Honda Gx160...

Another project that never happened. Paid $60+ shipping, sell for $50 shipped. :scooter:

Want $50 for the head. It's nice! Has valves, rockers, springs all still installed. Never been raced, was an industrial engine. Raises compression over 2 points if put on a gx200 or 6.5hp clone motor. PM if you have any questions. Thanks!

Traveling for work so I won't be touching minis for about 3 mos. GX 160 14cc Head. I'm going to sell and regroup after the new year. See you at the Build Off! $65 Bare $75 with valve set. Located Brewster, NY 10509. Stuff is almost new.

GX140 14cc head. Same as GX160 just smaller valves. Wanted to install on one of my Predators but do not have time to clean and get into another project. What you see plus carb studs. Springs are new 18lbs. $35 plus shipping. Located at 10509 Brewster, NY

Parting out my GX200, Only been using my heavily modded GX390 lately. All prices are without shipping. Shouldn't be more than $5 since most fit in flat rate boxes. All items are "or best offer". No lowballs pleaseee! First up, the head. Recently painted with 500 degree enamel in Iron gray. No...

On my old engine before I dropped a valve I put the 14cc head, with all the other typical upgrades, and I went thru pull cords and recoil springs like crazy, it would snap that thing right out of my hands all the time to the point I would give up if it wouldn't start easy, found my flywheel key...

Hi, I have a 14cc clone head, complete with rockers and studs, clone valves and Honda or clone stock valve springs. All it requires is an exhaust retainer and rotator. Good condition, little use. Pictures can be had on request. $50 or an offer. Don't hesitate to send an offer, the worst I can...

what is this? I have a spare engine laying around I think its a 5.5hp so it should be a 14cc head from a gx160... Was wondering as well if the stud kit from the predator would work on this cylinder head because the valve studs were stripped on this cylinder head... I'm going to slap...