aftermarket

  1. Bruceo

    Any aftermarket parts for a 420 predator

    I just bought a HF 420 and was wondering what Aftermarket part are available? i was hoping ,Billet flywheel,rod ,valve sprngs,pushrods,rockers,cam. anything and where to get them. Thanks
  2. Clayon

    IDing some aftermarket cams

    Hi guys, I need some help IDing some aftermarket cams for my Briggs 5hp FH. They are from Halls Racing Engines, but I believe they may be regrinds. Since I don't know how to degree cams I just used a caliper to compare the stock Briggs cam to these and they are definetly bigger. The cams...
  3. M

    Tecumseh Aftermarket Carbs

    Anyone have any luck with aftermarket carbs? I have two H50's that don't seem to run right no matter what I do with an aftermarket Oregon carb I bought a few months ago. The engines run way better with an old Tecumseh H30 carb. Just wondering if I got a dud Oregon carb or they are just junk...
  4. D

    Aftermarket Flywheel?

    SO ill be doing the basic mods to my clone. Timing. 390 carb 160 Head (ported) rockers and springs remove govoner sparkplug indexing custom exhaust. Cam (dunno if needed)(what one) My question is how Important is a aftermarket flywheel. how are the steel ones? I dont wanna brake bank.
  5. countstevula

    Manco Big Cats with aftermarket tires (not stock knobbys)

    Anybody got some on their big cat? I'm thinking one of these kinds....
  6. jspec

    aftermarket air filter & gas tank on a predator 212cc

    Will this fit right on here? GX200/Clone Air Filter Kit Also, I've seen some guys on here with aftermarket fuel tanks they're aluminum and cylinder shaped but I cannot find any. Where can I buy one? I was planning to check out Lowe's tomorrow. Thanks for any input!
  7. Dodgeboydan

    Clone aftermarket flywheel

    Looking for a gx200 clone flywheel. Any manufacturer preferably billet Aluminum. Does not need to be adjustable
  8. Cleturner

    aftermarket motor

    hello all i was wondering if it were possible to put this motor on my indian papoose? please help
  9. Gpro13

    aftermarket scrub/break heathkit boonie bike

    I have a heath kit boonies bike and I need to know if there is any aftermarket scrub sprocket and drum breaks avalable for it. I do know the drum breaks don't work so well but its more for looks then anything else any help or advice on this matter will be greatly appreciated ideally something...
  10. C

    Best carburetor for intek 206

    I have an intek 206 and am in need of an aftermarket carb. The stock one just isn't cutting it anymore. The real reason I want a new carb is there is no adjustment to it and it's running really lean I've cleaned it and decided I needed a new one. Then I thought why replace when I can upgrade...
  11. creia

    Aftermarket (performance) air filter on a Predator

    I am sure that many of you have already done this, and I'm looking for some guidance from anyone experienced.... We're planning on doing the "usual/typical" mods to the HF "Predator" we just purchased (e.g., re-jetting, performance exhaust, performance air filter, etc.) just like we did way back...
  12. delray

    aftermarket carb for my briggs

    i been looking at some mikuni clone style carbs for my stock 5hp flathead briggs and was wondering if any you guys have done the the samething and what size carb has work the best for your "STOCK" engine. the only mod will be a header pipe exhaust system. for example a 19mm carb or something...
  13. 1

    Aftermarket wheel for CAT

    Hi, I picked up what appears to be a CAT 350SS frame. The original front wheel was rusted out, and the back wheel was not stock. Does anyone know what size Tri-Star alum. wheels and tires will fit front/rear (either 3",3 1/2", 4" and 410/350/6 or 530/450/6?) I have a 4" Tri-Star wheel...
  14. C

    gx200 clone aftermarket parts for sale

    I got all after market parts from Agk for sale. 260$ shipped.. located in Bakersfield ca -22mm mikuni Carb -billet Carb adapter -18 lbs valve springs -caps and retainers -.265 cam - 14cc head - two stage exhaust - uni air filter -grade 8 bolt kit I have stock parts if need any pm me.
  15. R

    AfterMarket Carb

    Hi all, I'm going to my first Mini Bike swap meet in Saline Michigan this Saturday. I have a 3HP briggs motor with a cast iron flywheel.It has a Flo-Jet carb and oil bath air cleaner. I would like to change it any ideas what will work? Thanks, rjs444
  16. Ibanez616

    Cast aftermarket flywheel?

    I am looking into a flywheel a fellow has for sale, and its cast, but not stock. Any idea who makes it? He says Dyno Cams sells it. :confused:
  17. jesse8931

    briggs and aftermarket carb

    So I have alot of 5hp briggs motors and have only really used one witch threw a rod with the governer removed :shrug: but anyways im cheap and have them so i want to use like a pz or mukuni clone on a few and wondered if any has a angled intake like a 45 degrees or close
  18. The Restore Kid

    Honda CT70 aftermarket racer intake

    I tried to find the thread to no avail... I posted it a long time ago completely confused as to why this thing looks like it does.. :confused: Someone wrote in and said they were designed and sold as after market parts back in the day so that you could ad a larger carburetor to your trail 70 and...
  19. ct70

    ct70

Top