aluminum

$50... fits 5hp flatheads, painted wrinkle black with the fins sanded off for an old school look.

I have some parts I won't be using, so please take advantage of me! Chrome throttle with grips and kill switch, $15.00 shipped Briggs 5HP muffler (3/4" NPT) for $15.00 shipped Giant Tecumseh aluminum pull start for $25.00 shipped. 8HP I think. Measures approx 6 3/8 from hole to hole

I've had this ('61-'62) Super Savage for about 3 years now just sitting in the corner. Somebody ( a long time ago) had put a little 4 cycle REO engine in it. It was cool but not correct so I sold that off and began my search for the proper West Bend 580 motor. Now there are West Bend 580's for...

looking for the 5" aluminum drive wheel with the 6 holes drilled or not.

Doing my best to figure out how to put a torque converter on an old Alexander Reynolds . It's interfering with the scrub break. Had some aluminum pieces made for it . Not real thrilled where the gas tank ended up .

i needed to take a break from writing code for the electronic system so here's what i did today: a while back rayvel shipped me out two cast aluminum bonanza kidney bean wheels that had chucks removed. i filled in the missing chunks with aluminum wire that the mighty mig welder deposited. the...

What are you guys using to clean aluminum? I have some Rupp wheels that have turned white,I can put them in the bead blaster,but if there is something I can soak them in and remove the corrosion I would rather.I know that on some old car parts,namely zinc and aluminum tag plates,I soak them in...

i finally dragged out the spool gun i bought a few months ago to see how well i can mig aluminum. not so good: blobs, little penetration, not sure where to start. i can mig ferrous metal 'ok', not great, but this welding looks worse than a cub scout den project. obviously i need...

ok, I suppose I could surf the internet and get my answers, but I know there is much talent on this forum and I wish to find out if any of you can answer my questions regarding smelting...since my nephew moved in with me, I am trying to expand his horizons and I wish to learn new things as...

What brake drum (for band brake) do I need to bolt up to a 6" Manco aluminum wheel? The bolt pattern on the one that came with the bike doesn't even come close. Thanks for your help. Jerry...

I have a set of Alton 6" aluminum wheels with hubs and new bearings. I have no idea what these are from. One wheel has some abuse, but behind a sprocket you'd never notice. These have been blasted and come with new bearings. $75.00 shipped and they are yours!

I have an aluminum pull start unit that is in good shape and works well. Looking for $15.00 plus shipping

Been meaning to post this and so its snowing and have a few minutes. This is off Kohler XT149cc vertical lawn engine. I didn't have any time to mess with so gave to Tim. Said it fit Honda taper. My hunch that it would fit Hemi Predator because its Kohler. Tim said it did not.

I recently purchased a Manco Minibike that is a mechanical nightmare. My question is: I have the Manco aluminum wheels and I need to know, Is there supposed to be a spacer tube in the wheel, between the inner bearing races to keep the outer spacers from putting pressure on the the inner bearing...

Frame straight, one re-weld by previous owner behind motor plate which I would redo if I was keeping the bike. This is a usable frame with swing arm. Forks are bent. Aluminum wheels nice, attaching metal rims pitted. $75

I'm looking for at least on half of a Manco aluminum Minibike wheel. I have one with a broken lip for the tire bead. Let me know what you have. Thanks for your time.

These are from a GX200 Honda generator. Shroud is all aluminum. Has some tar on it in places but some elbow grease will be fine. I believe a gx 200 long starter cup will work with shroud or some how making a cup longer by cutting and welding. The coil is a big block coil and the bracket is to...

I am picking up this Old Briggs aluminum flathead any body have any knowledge on this. Thanks

Anyone ever use DWT wheels on a mini bike I would like to hear what you think about them ....

Thought some of you might like this. Published on Aug 18, 2013 Bay Weld Boats of Homer, Alaska construct this vessel in a week's time. Enjoy watching it in just a few moments. https://www.youtube.com/watch?v=UGAOozbxsRM#t=35