bearings

I need a set of bearings with an outside dia of 1 3/8" that will fit a 7/8" shaft. Where do ya'll get your bearings?

A neighbor brought me her son's DB30 that is in ROUGH shape and wanted me to fix it up for them. One big issue I see is that the front end is really loose, looks like nearly all of the bearings are gone. I see posts about people switching over to the sealed bearings. Before I take the front...

I did a search and found this mentioned before but not resolved. I just got my TS working and have gone through two sets of wheel bearings on the front. These weren't the stamped wheelbarrow bearings. Has anyone found a bearing that works well for these? All of the high speed bearings I've found...

Complete set of Aggie or KOL wheels. Includes front and back wheels, used tires, original axles, bearings, sprocket...etc... The prior owner spray painted them. Asking $150 plus shipping.

I just started work on a mtd Columbia. It's my first mini and I have no experience with this stuff. It didn't come with a rear axle or bearings. Does anyone know the correct axle and bearing sizes for me to order?

RUPP TURBINE WHEELS with Tires, Tubes, Sprocket, Hardware… front wheel Unpainted, chrome great, with vintage 4.00x6 Carlisle … sometimes a 4.00x6 fit where a 4.50x6 doesn't (Continental 250 forks) REAR WHEEL also in great shape (painted, with stainless hardware...

Hey yous, what type and size bearings am I ordering for these Roper wheels? And the rear wheel on the right has a spacer that not only goes the length of the inside wheel ,like the front on the left does, but sticks out on both sides. Do I need to keep it like that or can I get new bearings...

Do they make wheel bearings that fit pocket bike wheels that adapt to a 5/8 hole???

I have a set of Alton 6" aluminum wheels with hubs and new bearings. I have no idea what these are from. One wheel has some abuse, but behind a sprocket you'd never notice. These have been blasted and come with new bearings. $75.00 shipped and they are yours!

Set of four Wagner flange bearings. 1 3/8" OD 5/8" ID. BRAND NEW OLD STOCK from the 70's. Made in the USA!! Very similar to the type used in Cat and Bonanza minibikes. Will be shipped DRY, like this unless specified: Or I can pack them with some good quality grease...

So when I did the tear down on my bike the bearings on the wheels were junk. So I chucked them in the trash and saved one so I could remember the size. Well I cant find the one I saved. So I was wondering what the size is so I could go on OldMiniBikes warehouse and buy some. Also what is the size of the...

I will preface my question by saying that I am new to mini bikes and mini bike repair. Attached is a picture of the jackshaft on a mini bike that I am going to restore. The bearings on one end of the jackshaft are coming apart so I'd like to either replace the bearing or maybe the entire...

Pair of pretty nice Go-Power wheels.5 inch,no denting or scuffing,the rear has a little pitting on the inside ridge.Rear has a sprocket.I have NOT tried to take these apart,so the allen head screws are not stripped or rounded out.The tires look to be nearly perfect,they are General Jumbo...

Anyone out there with tips or instructions on how to safely remove original bearings without breaking them? I have two on the front fork neck that need to come out prior to painting the frame, and I also have two which are part of the jackshaft assembly which look like they're held on to the...

Does anyone know of better wheel bearings for the Baja Heat/Warrior? I want to install higher quality bearings for higher travel speeds and longer bearing life.

Gone through completely with parts from Ron Kimble, not restored to 100% but it's damn nice. Tank is intact with no leaks, 10hp Tecumseh pull start only but starts easily. New upholstered seat over original foam with new underlayment on an ash plywood base and it's bolstered as the original was...

Howdy,We just replaced all 52 steering bearings in the front handle bar/goose neck area.. Does anyone know how these should be adjusted properly ?? 5/32" bicycle bearings steel chrome.. Any help great appreciated.. Thank you, Marilyn.. :hammer:

Has anybody had their wheel bearings fail or wear out ??? It seems like they would be susceptible to failure especially with a bigger engine swap. Can you get American made bearings to replace them ??? Anybody got any part numbers for that ???

Looking for the older style Heim bearings that had the solid flange and a metal shield on both sides...1-3/8 o.d. x 5/8 i.d. Looking for NOS or like new condition....PM if you've got them or a source for them. Thanks

picked up a track 2 a while back broke it down and today picked it up from the powder coater. I then went in search of a nut for the top of the fork stem with no luck. Took the tires off the rims today and beat the bearings out as they felt crunchy. I have a new in the box predator hemi to put...