I sold my tote gote mini gote a while back and just yesterday I got a call from the new owner.
He said he loves the bike, but wants to get a replacement belt for it. I believe the belt that was on it was the original one. While I had it and rode it I noticed the belt was slowly...
I have a decent used North American belt clutch for sale.
3/4" bore, fits A or B size belts. Used on dirt compactors. That's what it was on when I got it.
I never did test it before removing it from the engine, but everything looks like it's in good working order.
Asking $65 plus shipping...
Ok, I think I have a 20 series drive clutch and a 40 series driven and I want to make sure I get the right belt (if there is one). Center distance is just over 7.5in and is adjustable to be less. I am not sure what info to provide but below are some pictures for reference. Please help!
So i was about 2-3 miles from my garage where i keep my sears roper mini bike, As i was turning around, the torque converter belt came apart, like stuff was flying through the air. Does any one know what size V belt i need to get:confused:. thanks
I have a knock off tav2 and the center to center measures 6 3/4". The 203589a belt is for 6 5/8" - 6 11/16" and the manco 5959 Is for 6 15/16" - 7". I'm right in the middle of both of these, what should I use?? The driven clutch is centered to the backing plate.
Any ideas?
I want to replace the belt on a old Torque-A-Verter bike lit. says its part # B-1038 7" Asymmetric / Mod # ZCQ-18735A
73 or 74 yr. numbers aren't helping me on my search... I have 6" Driven Center distance 6 5/8" - 5/8" top width.
The charts are very confusing & I'm not finding any chart with...
I am cleaning up my torque converter now and wondered about the inner surface that the belt rides on.
I attached pictures of the drive unit, and I knocked a bit of the rough stuff off the surface but didn't want to take it too far.
The picture maybe makes it look worse than it is, it's...
I recently purchased a chinese knockoff Tav 2 for my predator212 mini bike. It was kind of a pain to install( had to raise the motor in the frame to clear the mounting plate and driven pully) but I got it on and working. Now when I roll the bike forward, the friction from the belt on the pullys...
Got a nice vintage v-belt clutch for sale. No name visible on the clutch itself.
Spins freely, decent shape. Collar is a little beaten up, but is only cosmetic.
5/8" bore.
Asking $40 plus shipping.
PayPal, USPS money order or cash.
Well was out riding yesterday and went down to the hot rod shop to hang out . My buddy Craig took the Powell out for a ride , mainly cause he has never seen a Tecumseh turn 6300 and live .
He took it down the side street and then came back past his house busting it wide open , we lost site of...
MTD Rambler belt cover in great shape with mounts. Rear mount will need stud welded to it.
It has been sandblasted but you still can see the faint outline of Rambler on it. Has fingerprints on it from the shop so will need quick prep before painting as you should do anyway.
This is the early...
from my research on here its for a climb away assy. This is NOS out of an old dealers stock, actual Bohnam marked belt 4-7079 only one I have and no other TG parts so please dont ask.
$38 shipped
I have mid 70s sensation go devil with a comet converter set up but the belt is missing I ordered one from OldMiniBikes per the questions I was ask as for as mesurements but the belt they sent is to tight and will not slip at idle dose any one have any idea what belt I need to order next ? Thanks Eddie
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.