block

  1. R

    New El Tigre on the block

    Hey Just bought this little bike for 20.00. Needs a lot of work but will be fun. Taking all part and trying to go back original . Will keep posted of progress.
  2. D

    Briggs 60's models in the small block

    Years ago, (1969) I obtained a used Lil Indian with a Briggs & Sratton flathead on it that looked to be the same physical size aluminum block engine that the standard 3 hp was. It had no sticker on the blower housing, was recoil start and looked like a period 1965-1970 3hp flathead. Had the...
  3. J

    Original HS40 block stamp

    Hello, Picked up a 1970 Lil Indian 7000 today. Had an HS40 on it. Block was bad but here is what I saw on the bottom during tear down. Including the shroud numbers as well. HS40-552848 0092 12787 Might help decoding Tec motors. This one also had the Minibike specific throttle hook up etc.
  4. wildman500

    go really fast parts(3inch small block stuff)

    So I'm too fat for small blocks so its gotta go:blink: First up I'm selling a complete 3inch honda with big valve head.Mostly new parts. honda motor with 3 inch bore (fresh/new) honda crank(used) 32/28 big valve head w/ti valves(fresh no runs) 3.707 arc rod(new) 2.992 piston(new) isky...
  5. C

    venting the block

    ive searched on here for some info on when you need to vent the block,ive found a few treads but they don't say when you should do it,i have a honda gx200 with the following done. billet...
  6. leathernun666

    Need Tecumseh big block thottle part

    Anyone have one of these for a big block or know where I can find them ?
  7. R

    WTB: GX200 or clone block

    I lent my friend a piece of equipment with a GX200 engine last winter. I'm not exactly sure what he did, but he sent the rod through the block, so I'm gonna say it was oil related. Anyway, I'd like a clean bare block.. I'm in Cincinnati, Ohio.
  8. O

    Painting Clone engine block

    Can you Paint these blocks? if so need any kind of special paint? Thanks
  9. jeep4me

    Newer small block 5hp Briggs ????

    On a recent trip to the scrapyard, I pulled a 5hp Briggs out of a single stage Craftsman sonwblower. The cover on the snowblower was labeled as a 5hp with electric start. I have worked on a number of these newer 4 stroke single stage snowblowers and knew that they had nice briggs flathead...
  10. MB165

    Aluminum welding question/ Hm80 block

    Anyone know what alloy number tecumseh used in their blocks? I have a HM80 snow king with reverse shaft im hacking off today. Will turn out a plug for the hole in the side cover then Id like to weld it in. Anyone done this before? Pete
  11. delray

    ken block driving

    just something to watch.....:smile: crazy driving this guy can do....... Ken Block's Gymkhana THREE, Part 2; Ultimate Playground; l'Autodrome, France - YouTube
  12. 5

    Rebuilt Briggs 5.5 hp I/C Long block 3/4" Keyed PTO

    I recently rebuilt this engine and have already sold the carb & tank setup. It came off of a Craftsman Rototiller rental and was said to have starting issues. When I took it apart it was easy to see that it was well maintained with frequent oil changes. Clogged pickup tube seem to be the...
  13. Dave_In_Florida

    Need pics of big block Heat/Warriors

    I have a Baja Heat/Warrior and just purchased a 11hp clone and clutch for it. I know the swap has been done before, but I'm having a hard time finding pictures showing how the motor is mounted and what sprocket setup is being used. The clutch I got has a 17t sprocket on it, and I'd like to...
  14. edwin

    honda gx 200 block and side cover

    block for sale perfect condition to build up. located in so cal, asking $100 shipped......OBO
  15. R

    Real Honda GX160, 5.5hp Block and Crank

    I have a real Honda GX160, 5.5hp that came off some kind of pump. The guy sold it to me because the bolts in the side cover broke off. It was running fine, but he didn't want to mess with it and bought a whole new engine. I wanted the head and a few other parts, and I have no need for the...
  16. C

    Fresh B&S Flathead block

    Block for sale. Never ran it, Cast Iron Cylinder Dual Bearing Freshly honed Fresh Hi-Temp Black paint I will include the lifters and the valves, along with the shroud. No flywheel, rod, cam, piston, or springs. I'll get pics eventually. $50 + shipping OBO
  17. S

    honing tecumseh aluminum block

    hi im new here just trying to find out if its possible to hone an aluminum bore tecumseh. or is it better to sleeve it . i have the means to do it either way but my friend who's a automotive rebuilder says you cant hone aluminum bores they will wear out prematurely. but the lawn mower guy down...
  18. leathernun666

    Wtb tank brackets for big block Tecumseh

    I am looking for the tank mounting bracket for a big block Tec that lets you use the small tanks. Like the one in this pic. I have the big tank mounts , but I need the small one for clearance issues.:thumbsup:
  19. 125ccCrazy

    blower housing big block Tecumseh H50, H60, H70, HH60, HH70

    Looking for a clean straight blower housing, NO starter bump..... I don't care if it has the two threaded inserts above the recoil, I can weld them shut.... Just need a clean cover.... (recoil can be optional)
  20. J

    Powder Coated Long Block

    Thought I'd show off my long block assembly I just got done powder coating for my second Baja. I used a Matte Black powder and masked off all the matting areas before spraying. 15 minutes at 375 and this is the result... I'm really happy... :) I'm hopefully have everything back together...
Top