cable

Well I got about 4 hours of fun out of the new Streaker before I was flying (and I mean hauling ass) down the road then, snap, I broke the end of my throttle cable. any help would be great. Im gonna try to rig it or should I just try and get a new cable? anyone else done this before...Im sure I...

I have a complete and running 1972 Moto-Skeeter 350. The petcock fuel shut off is wore out and leaking fuel out the valve handle. The throttle cable has broke along with the nut that secures the cable into the throttle handle. Looking for replacement parts...thoughts?

I have approx. 40 ft of NOS cable housing. This is the old stuff that is metal lined not plastic. The outer shell is lite grey in color and just slightly textured. Perfect for an older restoration. $1.50 /foot or $60/shipped for all of it. I also have one brake cable with red cable housing...

As some of you know, I just finished cleaning up my 69 sprint. It had zip ties on the brake & throttle cable originally holding them to the frame. There were only two of the original zip ties left on it when the bike came to me. I went ahead and put zip ties back in the locations they were...

HOW TO SOLDER Throttle & Brake Cables - YouTube Just thought I would share this with everyone. I know everyone on the forum has said just solder on the end but this is a detailed video on how to do it. I tried many times to do this in wood but it didn't take so well. The methyl hydrate (or...

I made a metal lever that installs the throttle cable at the back side of the motor using the existing clamp and screw. I call it the R67 rear throttle lever. :smile: Use a hardware store 90 degree angle. File the notch in an angle and round off so it doesn't bind with the other...

Hi looking for a 1inch brake lever and cable for my bonanza i have in the project section thanks.

I need some help finding a whole throttle set up that will work with the mikuni on a mini bike. Been looking around on ebay, but don't want to make a wrong purchase so hopefully some of you guys can help me out. I was looking at this Throttle Cable Clamp SDG SSR CRF50 CRF70 CRF100 XR CRF...

Hi everyone, Just getting the last bit of my build together. I was just wondering how much travel you are all getting from pulling/twisting your throttle mechanisms. Currently I have a brake lever cable that I use for a throttle, see picture below. I have switched to the raptor...

Okay just got new levers and cables for my super bronc from OldMiniBikes warehouse :thumbsup:. ?? is they are a little to long if i cut the conduit can the little chrome end piece be removed and put back on ? :confused:

Does any one know how to change a trottle cable on a tote gote?

The one on my bike is 38 inches and is too long.

I'm not around the bike right now so I can't take a measurement, but I'd like to go ahead and get my new grips and cable ordered if possible. Can anyone give me a definite answer on a throttle cable length for this setup? The ones I'm seeing are typically 48, 53 and 60. Any of these fit the bill...

Does anyone have a good source to buy a throttle cable to fit my mikuni. Right now im using an oem replacement doodlebug cable (48" conduit i think) and its just a little short. I got an azusa with some tall handlebars and i think about 65" would fit allot better. I would rather get one that is...

Like the title says I'd like to pick up a set of throttle grips along with the cable if you have one I'm in the tx area anywhere near ft hood, san Antonio and in between. Shoot me a pm if you have a fair offer

I have noticed that on most twist throttle assembly's their is not a way to hold the cable housing in place when you let off the throttle on my last build I used safety wire and a friend suggested using shrink wrap . so what do you do? :confused:

For sale: minibike throttle assy, cable and grips. Good useable shape, its off a DB 30 but will fit many others. $22 shipped to lower 48. 7/8" bar

New parts, Fuel tank, Throttle cable, and LED Light kit.

New parts, Fuel tank, Throttle cable, and LED Light kit.

New parts, Fuel tank, Throttle cable, and LED Light kit.