cam

How many times have you took a lawnmower motor apart and found a plastic cam? What is the chance of failure if I remove the governor and rev it? And another question. Is there a vertical shaft motor out there that uses raptor parts?

Can you tell a difference in idle and sound with this cam just curious thanks

Head & Bolts. Hot tanked, with 3 New head gaskets Flat, no cracks, but has very small chip on one fin. Gas tank, with top bracket. a little beat up, but No leaks. Sidecover and Bolts. Cam, and tappets. But wait, there's more! A brand spanking new #35 master chain link. $60...

Does anyone know if this cam will fit the tecumseh ohh60 New Tecumseh Dyno Cams Camshaft 255 OHV 5 5 HP Race Kart Parts | eBay Also if it does how much different is it from factory? I have a robertson's torque tube, an adjustable hs50 carb, and a cone filter. If I can find all the...

Is this a good cam for torque and mid range power? Also should I upgrade to different carb? Does it sound good? Just curious because I am wanting to buy one seem like a lot of people like these cams. Thanks

What is the best cam to use for drag racing? The engine is a Briggs WF. stock valves. 1.3 rockers and a Mikuni tm24. Later on will be shaved about .050" and larger valves. Distance is 1/8 mi. Minibike is the vehicle.

I cut down the cam shaft because it stuck out of the side case. This is temporary as I will be changing out the side case soon. The new side case will not have the hole for the cam shaft to protrude through. So can I cut down the cam shaft to fit or do I need to buy a different one? Thanks...

Ok i got a brand new box stock project engine just put in a black mamba cam a 22cc head milled .65 26lb springs and 26/25 valves this is my first engine I did I can't seem to get the valve lash set right when I tighten down on the 10mm head screw holding back the 14mm one the gap closes to...

Well hi. I'm new. Any way lets get to it. Everyone knows how Briggs blows air out the carb right? Advance the cam a tooth. Way more compression. I will run it tomorrow and post results. I'll try to get a picture of my mower to tired though. I hope this is a new idea.

What is the best over all cam on the market that i wont spend too much money on. I was looking at the CM grind cam but not sure. Thanks

I can't seem to find the lack Mamba Jr Cam & 26LB springs in stock for the Hemi motor. Any idea where I might find one?

MTD trail flite 212cc dyno cam 18lbs springs .032 jet header air filter DB30R gc160 header

Used but in great condition Dyno Cam 94-5 High Rev. for Briggs 5hp Flatty. :hammer: $25.00 and free shipping

I installed a header, dyno cam, and 18lbs springs. It idles perfect but one you give it throttle it hesitates and backfires. And if you give it throttle and hold it, it has uneven rpm and like its restricted. I DONT HAVE INTAKE OR BIGGER JET. AND STOCK FLYWHEEL. .....HELP

I installed a dyno cam inst my preadator and it has crazy compression. Almost pulled shoulder out trying to start it. I tried lashing valve and didnt work. I have ordered 18lbs springs. Only mod I have is header. WHAT IS THE PROBLEM? HOW CAN I LOWER COMPRESSION SO THAT I CAN START IT?

im getting a dyno can and 18lbs springs for my 212cc but it says that the cam is only for no hemi blocks. Is there any other way to id a hemi from a non hemi other that valve cover? I heard something about non hemi has black carb studs

I have a Baja Warrior with a 196 clone. I was just going to repair the engine and slam it in the frame of this bike, but with how easy and cheap it is I somehow ended up with a shaved head, .036 jet(stock emulsion tube), aftermarket air filter, Modified rocker cover with PCV valve and breather...

I picked up an HS40 recently that has a reverse shaft on it. The engine is in great condition so I was thinking about swapping the side cover and cam out. I picked up a blown HS50 last week. Can I use the cam, crank and side cover from it on my HS40? It would be helpful to know before I pull the...

Ok guys, I've done a search but I really think I suck at the proper search terms so bear with me. Like the title said, I'm doing my first Hemi build. So far I've gotten all the gaskets I need, side cover, .010 and stock head gasket, and various others. Got an ARC +.020 length billet rod, and...

Hey guys, first time using the forum :) basically i have an old kt100 kart frame that needed an engine. So i went to harbor freight yesterday to pick up a 212 to build. They only had the 730 models everywhere untill i saw a random engine out of the box just sitting under a shelf. I asked a...