camshaft

I have a predator 212, it has a lot of mods: RLV header K&N air filter Jetted Carb (stock carb) CL1i Cam Milled GX160 head & ported Big :censure: valves Fuel pump no gov 26 pound springs I know, I know I don't have the billet flywheel or rod, I'm in school and will get them soon! What is the...

new to the site and would appreciate any advice i can get. Having trouble choosing a new cam. Engine is powering a modified baja heat. Not track ridden or raced, just an around town and country bike. looking for higher rpm without killing the low end. dont need a torque monster just descent...

I have a cam for sale, it's an Agkcam265M made for bigger than stock carbs in a GX200 or clone. .265" Lift and 236 duration. Use 18lb springs with this. It's in excellent shape with low hours. I paid $50.00 for it and will part with it for $25.00 plus shipping OBO. If interested, email me...

I was wondering, if you had for instance, a stock 5hp Briggs, and you dropped in the highest performance camshaft this otherwise stock engine could manage, how much higher would the HP be?

Well, awhile ago in December (before Christmas) i bought this 3.5 H.P engine from tractor supply, and when i went to open up the crankcase and WTF? a plastic camshaft? c'mon you gotta be joking right? like you can't modify it or anything like in ChargerMiles007's video YouTube - ‪Modified...

I'm going to try and remove a crankshaft from a tecumseh 10 hp hm100.. anyone have any tips? i just drained the engine.. now what?

Like new NR cam 285 0607. Has maybe 3 hours run time, 30 minutes of which was on the bench with 12lb springs for break-in as recommended by NR. Combine with a ported head to make 15+ HP $75 shipped to 48 states. Or pick it up 20 min north of the D for $70. Comes in original NR box PM if...

I took this engine (Tecumseh HS40) apart nearly 10 years ago and have no memory of the disassembly process. Anyways, the repair manual talks of a component called the "compression release mechanism" on some engines and as there is a hole machined into the gear (see below) I'm concerned that I...

hi, im trying to rebuild a hm80 155052a for a super bronc but am running into problems finding a camshaft... listed as part number 33366.. anyone?

Need a 5hp single shaft side cover for Briggs horizontal shaft mill, also stock cam. I currently am rebuilding a 5hp Briggs off a rototiller, and the power reverse take off shaft and camp are one unit, can't remove it and plug the hole, so I'm looking for a side cover off a non-rototiller...

I have given myself the choice of either buying a new camshaft from AGK or a aluminum flywheel from AGK. I HAVE removed the governor and I have heard people say that the flywheel can "let go" and I have heard people say that the camshaft can too. Just a question of what to buy.

Hello, all I was looking for a good 3hp briggs camshaft Thanks for reading.................BANDIT:thumbsup:

Hello, We race 1/4 midgets, We run a 82252 3hp Briggs The motor is basically stock other than intake & exhaust porting and 5hp springs. We run a 182 walbro carb and a aluminum flywheel set at 31 degrees We also have a 6 to 1 gear reduction and open exhaust. We gear the motor to run between...

Hey guys, I purchased a .285 lift cam from NR and am about to install it. My question is: Do you guys think assembly lube is a must for break in? I'm going to run the stock springs initially as per the instructions on the package along with 10w-30 synthetic. Is that sufficient enough? I...

Now here's a topic that could keep you learning for the rest of your life. What do we, as a group. Know about the various camshafts on the market, that are best suited to the engines & type of usage that we commonly enjoy? We have our: 5HP B&S Flathead 5HP Tecumseh Flathead 6.5...