Clone head
28.5/25
Milled 65k
Ported
Ss valves
Dual springs
Billet retainers
Billet rockers and guide plate
250$
Head was on a drag motor that went 9.80
Turned 10,200
I have a intake for sale that bolts a mikuni 22mm to a clone or predator . It's made to where the carb sets above the motor and faces forward , this manifold is made to bolt on without a top plate to keep it low . From bottom of motor to top of carb is about 14 1/2" s . Also made for a flat...
My son races a outlaw class with 120 snowmobiles. The only rules are no exotic fuels and max 212cc. I just bought a used modified clone with the following done to it.
Hemi predator block
De-stroked +.17 clone crank
+.20 arc billet rod
Pvl flywheel
Gx200 billet lifters
Chromoly push rods...
Engine won't start now
So I removed the governor today, made sure the cam dot lined with crank dot upon reassembly.
I made sure the new linkage kit allowed throttle to return normal and it did. I checked spark and it's there.
Fuel tank is full.....
Motor turns easy by hand and sounds...
Hi all!
I am in the process of getting my Baja mini bike back up and running. I have received my new carburetor and put it on the bike. Unfortunately during disassembly I wasn't very smart and forgot to get good photos of the throttle setup. Below are the photos I do have.
I am...
I got hurt recently and could not ride so my mild build clone sat for 4 months. I was an idiot and did not put any Stabil in it. I recently tried ot start it and no go. So I took off the Mikuni 22 clone and cleaned it out. I took out the needle and seat and the two jets. Blew carb cleaner...
I saw this on Bobs it is a copy of the old Honda head and Mike from cloneenginepartsonline.com has them for sale. While I still like the hemi it lacks a squish area unless welded which causes other issues. This head has two squish areas and a sort of fast burn design with tapered walls. This...
Hey guys im new to the form gonna be doing a full engine build on either a 5.5 or a 6.5 honda motor i have looking for some imput if anyone has built oneband would like to share the specs and speed it did i would appreciate it alot thanks for the help in advance :)
Hello i have a Honda Clone motor. it is stamped with a diamond and JD inside the diamond. the number on the block is 04s120601 and then it says JIANDONG. I got this motor on my trail horse when i bought it and was pretty beat up motor you could tell it was left out to rot for many years. if you...
Just wondering if any of the clone experts have an idea where to jet my clone carb .
My mods are .
Engine Tec HS50
Cam dyno 255
Tec Motorsports coil
Epoxied intake port reshaped
Ported exhaust port
Shimed stock springs
So I got her running today , started on the second pull ...
Can anyone lead me to where I can buy the throttle assembly? I got a grey hound (Honda clone) this past summer on a bike. I went to put stuff back together today and realized I was missing the stock throttle assembly. The PO removed it to put on a racing set up.
Thank you
So far I have modified my 6.5hp central machine clone with the following parts:
Governor removed
Header with rlv
140 emulsion tube and larger main jet
Uni air filter and adapter
0.020" longer arc connecting rod
Honda t3 flattop (1mm rings)
Arc 6619 billet flywheel
22lb springs
CM...
I know that the tolerances are all over the place for these motors so I am measuring piston deck height(amount piston in hole) as well as gasket thickness and head volume to determine compression ratio. My question is what is the average cutoff point where 93 octane can no longer be used and...
Removed low oil sensor and governor installed billet flywheel and con rod, dyno mod2 cam, 18lb valve springs , 22 mm mikuni carb, header and a 8.5 coil wire
What rpm do you all think it will turn
And how much hp will it put down?
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.