clutch

im getting sick of my azusa drum brake on my tote goat. It does not work for S#$t so i am going to install a clutch band brake instead. my clutch is apparently 4-1/16" in diameter. I am wondering if would use a 4" band brake or 4.5" ?

Just picked these up today. The 40 series driver and driven seemed reasonably priced and I have never used the 3/4 to 1 inch adapter before, so I thought I would give it a go. Not sure if anyone else has tried the 3/4 to 1 inch adapters. Thought I would share. Thanks 40 series...

Where can I get the crankshaft shoulder washer that goes between the clutch and the crank shoulder ? I cant find it, and I'm pretty sure there's supposed to be one. Project: Western Flyer SS300 with a new 79cc predator. Thanks, Dan

Looking for this style Sears Clutch Guard in good survivor quality condition. Please PM me.....Thanks in advance :thumbsup:

Let me know if you have one.. Thanks,Alan

for sale max-torque clutch spring, used for less than 20 minutes. one step above stock, 2200rpm. shipped usps from balt. Md. $10 cash, check, m.o. paypal accepted, buyer pays fees pick it up at windber $7

Can some one please explain the theory behind the different RPM ranges for the Max Torque Clutch springs? Mainly how the different RPM Ranges work on the springs.

How do I remove the Max Torque clutch from the 3.5hp Tecumseh motor? It has a grease fitting and bolt on the front of it. I can't seem to remove it. The clutch keeps spinning.

Frame has damage $195-original 4 speed clutch frame

I have a new never used Comet series 40 torque converter with belt and driven pulley The 2speed jackshaft is not included in this sale but is offered n another post. More photos here: grifftek.com/craigslist/comet_series_40_torqu_converter_wpcl/ Prrice is $175.00 shipping from 90242...

I have a new never used Comet 2 speed jackshaft clutch I bought for a project that never materialized. Price is $160.00 shipping from 90242 Torque converter shown in photos is available in a separate post and is not included in this sale. more photos here...

Need a few cat clutch covers. Short, medium or long its all good. PM me a price and pic. Also have cat parts to trade, if you need something. :wink:

I am trying to get this clutch off. 2 problems, No idea how to get that key out, & the allen bolt is stripped. What would you guys recommend.?

I have a Wards 525 that I recently purchased. It runs and drives well but it doesn't have the correct drive system on it. It is just a clutch with a belt to a fixed pulley. It works pretty good but I want more torque and lower "gearing" for acceleration. A torque converter gives that. While...

Do I need to move the engine to the right? I worked hard to center the rear wheel, which included placing a spacer in between the drum and back plate. So, I would rather not move the wheel out to the left. If I move the engine, should I order an engine plate before the re-location? or just cut...

Right now I have installed on my motovox a 212cc predator with 14 inch tire diameter, 12 tooth clutch and 58 tooth rear sprocket. Will it be okay to switch the clutch to a 13 tooth and the rear sprocket to a 53 tooth without burning up the clutch?

Two part question: Can the brass bushing on the jackshaft clutch be replaced, or should I just be looking for a new clutch? I ask because after putting this project back together, the clutch bell makes the same noise when freewheeling that it did when I was a kid (it sounds like it spins to the...

Hew everyone i remember a few years back that OldMiniBikes sold just the Clutch Guard Mount for the predator but i cant find it now, i can find the full kit but but i was just looking for the L plate that mounts on the engine, anyone have leads on them or able to make them?

Ok guys so posted a bit back asking questions on my mild build that has now turned a bit more wild. So basically ive got a doodlebug frame with a 212 hemi. Ported head with all the valvetrain upgraded, decked, wiseco piston, arc rod and flywheel, mod2 cam, and all the carb goodies including a...

Hello everyone, I purchased a clutch brake kit from OldMiniBikes warehouse and it did not contain any directions. I believe I got it figured out but need some advise. Pictured below is the way I believe it goes but was not sure about the 2 nuts. Are they for centering the band like I pictured...