Just plug in your Clone motor and ride.....too many projects so this one has to go.......$800.00 Will not take apart to ship, buyer responsible for pick up
Well i sold the original designed chassis with the nitro 44 from minichopperssocal - 909 minibikes
So i shall start a build thread finally of the new chassis im currently building...............pic is old chassis at track a few weeks ago with a torque converter on it.
So far i...
So started with a doodle bug and basically pictures speak for themselves selves... Tryed taking pictures as much as I could but a few were lost from switching phones ... I later sectioned the frame about a 1.5" so it wasn't soo high and got the top tubes closer to the motor .. Front tire is off...
What's up guys.
I'm 16 and pretty new to this whole mini bike building thing. I just recently got the skill of welding down, so I thought I outta build a mini bike. After searching the web on what model or type I was going to build I was set on a Trike drag type bike. So this is my plan...
Here is some progress on my jr Dragbike.
Its got a GX440 clone in it and will run a Jr dragster rear tyre and Bully turbo clutch.
More progress to follow complete billet GX440 to come.
What should i do on my clone for a drag bike? Its a 6.5 hp and i put on a header and briggs bullet style muffler, air filter and removed governer. So what else should i do?
Well after getting my other minibike running with the turbo, i've decided to make a new frame and change the style a little , since the old frame was made for a GX160 and i have a EFI Turbo GX390 in it, i can see it flexing so im going to make a new frame for it Below is how the old bike...
hello everyone ...new to this forum and i was hoping someone could gie me some insight on the steps in assembling a drag bike.... i have several projects but the motor is what i need to know about... i hear theres motors that can go 80mph... how does one do this?
Well I guess I'm in!! Open Class
I have been drooling over some of the drag bikes you guys have been building, so this is the excuse to build one.
I will be scratch building the frame , and will use a 16.5 -6.5 - 8 trailer tire for the rear and a 13 -5 -6 for the front.
The engine is a...
I was wondering where I need to look for part to build a dragbike specifically what axle are you running to use kart slicks and wheels for live axle and sprocket setup?? Who do I need to call minidragbike please chime in
The Double Whammy was built in two weeks to inspire another fellow OldMiniBikes Member to get his Twinibike done for the Billetproof Drags.
Got a great deal on a Doodlebug and a couple HF engines from Square Chopper here on the board, and thats what started the project rollin'!
Nice clean Doodlebug to...
Just like the title says, prefer something turn-key under $1000 near the Louisville KY area. Will consider shipping as well. Let me know what you've got. Need to find something by the 1st week of July.
Thanks,
Gavin
I noticed many of the drag bikes have 1 inch rear axles. Do you buy free spinning bearings, or use standard grease bearings? If you are using standard bearings, what are you doing to make them free spinning? Thanks for any replies. :-)
well here it is, no aluminum chassis but it'll get the job done.
motor has everything except 3in. piston and stroker.
.290 cam
1.2 rockers totaling to .315 lift.
246 duration.
still on gas.
YouTube - Drag minibike wide open
YouTube - Drag minibike gx200
Remeber this ugly thing?? Its going to be fast, small, and still ugly when i get done with it.
Plans to turn this into a drag bike with a 10" rear wheel and a 4" up front. Yes i will get rid of the cheapass seat.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.