governor

Well i have removed the governor, but now the bike seems to take alittle bit to get started. Anyone have any good suggestion to making this bike start alittle better? Because as of right now, it takes sometimes up to 5+ pulls before it will start, and i have to give it alittle throttle for it to...

i was tuning the HS40 (or at leats trying to), and the governor has like 2 pivot points, the setup is bad as it is, but the governor can turn, like thie pin going in the motor can turn, and the arm its on can turn, whats wrong here, i had it revving and it sounded more than the set 3600rpm, i...

Hi, I am posting a Terra-Cat rebuild in the project logs section. I need some advice regarding my governer control arm on my old Clinton engine. I am worried the lever within the engine may be bent. Check out this video link. Any help is much appreciated. MOV04034.flv video by...

I have a 5hp tecumseh bone stock and it ran good for about a year.Than when i ran it full throttle for a mile or two you could fell the governor kicking in big time more and more than usual so i removed the governor the gasket was old and tore so i used hi temp permitex and sealed it good ever...

When we bought this dirt bug the kids who owned it had removed all of the springs on the throttle linkage and governor and installed zip ties in their place..It wasn't working very well so I replaced the zip ties with pieces of wire linkage...It takes off decent now(compared to how it was) and...

so i lost the governor arm off of my 3hp briggs and i just wanna yank the hole thing out...will it last with the stock valve springs and other stuff???.. i havent seen any where where they have heaver springs for the briggs

I've done a ton of searching but haven't had any luck finding intelligible instructions on removing the governor on my Heat. The Heat engine is not like the Honda Clones...the governor appears to work externally to the engine. Has anybody done a write-up on this?

I have a 9 year old girl who will be riding a minibike,6.5hp with no governor. What will happen if I dont put proper springs in the engine and leave the stock ones in. She wont be beating on it, only puting around.

I removed my governor from my honda clone.Everything went well,I already orderd 18lbs valve springs and installed them do i need to install any more mods to insure i wont blow my engine

would it be 18 lb springs for this size? Would I notice a difference in performance? what about rockers, would different ones give me a "chop" type sound, like with a radical cam?

Hi Everyone, On the HF 6.5 clone engine, is there an adjustment spring screw just like the 2.8HP has? I want a little bit more RPM?

Ok, ok. Everyone has discussed and shown how to crack open the case and remove the centrifical weights and shaft of the governor from the clone and then plug the case. (great write ups by the way) My question is: Why can't we just disconnect the arm on the outside so it's not functioning...

Hi, After rmoving governor, Throttle is hooked correct concerning opening and closing but it feels like there is less turn when using the throttle grip on hanldle bar:confused:. Feels like maybe a 1/4 turn of throttle, I was wondering if this is normal because of removing the other pieces and...

Can you just remove the arm from the governor and rig the throttle or does it have to come completely out

Hey, just installed the 6.5 and I have no idea how to remove the governor. Please help! Also, with cjtmini's adapter plate, does the original chain work fine and does it line up the 2 sprockets correctly?

Hi there, If climbing a hill, does the governor automatically adjust the engines power on the carb?

First post here. I have a Craftsman tiller with a 5HP Briggs and Stratton engine (# 130202-3280-01) that won't advance beyond idle and I think the governor spring is stretched. Looking up the spring in the parts manual I come up with a 262310 "Spring - Governor Link", inputting that number at...

I just did my first 6.5 HP Clone swap, and on my db 30 mini bike, this new engine really provides some power. My question has to do with the "governor". I noticed in the throttle assembly there looks like a screw which limits the travel distance of the throttle, much like the speed limit...

Well i removed the governor on my 6.5 powersport and now when i go to start it the pullstart will lock up. but only at certain times. can this be caused by timing. i may have put the cam back in wrong if so could someone provide me a pic of the correct cam to crank lineup

I have a few questions on modifiying the governor on my Tecumseh OHH50 Power Sport motor..... 1) Do i need to get inside and remove all the internal Gov. parts or can i just remove the exterior parts? 2) Does the spring on the carb (that keeps the butterfly closed) have enough force to...