governor

I have a Hemi Predator on my DB30 and have decided it's time to remove the governor, low oil sensor, etc. I've done tons of searching and can't seem to find a definitive parts list anywhere. I know that's likely because there are 100 ways to accomplish this. The only thing I don't really know...

Hi I just removed my governor on my 212 with the basic stage 1 upgrade kit. I removed the low oil sensor, got the washer behind the governor, lined the dots on the cam up, did all the wiring correctly and checked the plug. The motor would not start so I took off the OHV cover and the engine...

I've worked on a lot of small engines, but I'm reassembling an HS40 for the first time. I think I have the governor assembly reassembled correctly, but I wanted to make sure that all the governor parts and especially the rod is in the right position before I close it up. I've looked at the...

Hi. I have the Canadian version of the Predator 212cc engine, the PowerFist 200cc 6.5hp engine. I am replacing the plug with the longer hotter one from GoKartsUSA.com, plus the upgraded cone airfilter and adaptor, their straight 1 inch exhaust pipe and screw on muffler, larger size 34 carb jet...

Is it possible to just adjust the Governor on a Predator or other clone 6.5 to just bump up the RPMs a little higher without having to remove it completely? I'd rather have the limit set steady at 4k RPM and restrict it there rather ran running unbridled. Thanks in advance.

Anyone know anything about small engines here? :) This mower sat for 5+ years. New battery, fresh gas, carb kit from OldMiniBikes, new plug. Starts but will only run at 3/4 choke or if I hold my hand over the carb throat, blocking most of the air. BUT.... it runs ok if I manually open/close the...

something is messed up with with all the crazy linkage on my briggs and after reading a few things was wondering if my engine will really grenade if i just bypass the governor? seems like some people said they left it on and just had linkage going straight to the carb and no problems. others...

Engine won't start now So I removed the governor today, made sure the cam dot lined with crank dot upon reassembly. I made sure the new linkage kit allowed throttle to return normal and it did. I checked spark and it's there. Fuel tank is full..... Motor turns easy by hand and sounds...

This is my first minibike and I am going to remove the governor. I have been doing a lot of research but I am getting confused with all these parts. The engine is a 212cc predator non hemi. 1) I am getting a billet flywheel and billets rod. Is #ARC6254 3.308" the stock rod size? 2) I...

I was repairing my mother's Baja Warrior Mini Bike, took off the gas tank, throttle cable and carb, but when I went to re connect everything, for some strange reason, the governor arm that goes in engine , is causing the throttle to be almost wide open when I re connect the governor spring...

This Christmas I am looking to remove my hemi predator 212 governor. I bought this engine a few months ago.. Anyways I want to know what flywheel, timing, billit rod, cam, valve springs, gaskets, anything else I need... I want to know what to get. I won't need any help with installation as I...

Hello Everyone, I'm trying to hook the governor back up on a 1969 B&S 5HP engine with tecumseh carburetor. The governor arm is there, but I can't figure out how to hook it up. A link to pictures on how this is done would be great. Thanks for your time and help, Lyle

I picked up an edger for $20 with the above motor attached. It didn't fire right away but after a quick carb cleaning I got it going nicely. Holds a nice idle and it's nice and responsive to throttle input. I'm new to these motors and was wondering if I could remove the "weather vane" governor...

I picked up a fox sprite a few weeks ago that had a Honda clone on it. In my guesstimating the motor that came on it was a harbor freight "greyhound". I'm not positive because I'm not actually sure I've ever seen one. Just heard talk about them. Anyway....... The po had all the throttle...

Hi everyone! I have a Baja Warrior with a Predator 212cc engine. I currently have it all taken apart to repaint, and I decided to remove the governor while I was at it. (And don't worry, I already ordered a new flywheel and rod.) I took apart the engine two days ago, and every since I've been...

I need some direction in adjusting the governor on a DB30. I know how to adjust the spring between the throttle linkage and the governor arm, but that's not my issue. I took some stuff apart to get things cleaned up a little bit and I think I may have messed something up. I removed the...

I have a Powerfist 7hp and I just finished installing the billet flywheel and rod but I am just curious if removing the governor is optional? Like is it possible to rev the motor to say 5600rpm or will it actually restrict the rpm? I don't know if I am explaining this clearly enough but if you...

This is the first time i've ever actually removed the governor. We've always just held it back with a spring. If i run it up slow it's good but, if i crack the throttle it hesitates & will die if i don't feather it. I have the aftermarket air filter(off for free flow) so it's getting plenty of...

I have a Baja warrior, I want to remove the Gov and install a Comet TAV, level 2 hop up, Billet rod and flywheel, and chrome moly push rods. What else should I replace? The hop up has 22lb valve springs, bored and jetted carb, billet flywheel, head gasket, and a race air filter and adaptor. The...

My HM80 has a lot of play in the vertical governor shaft and consequently, I cant get the engine to idle slow enough to use it. Can you tell me if there supposed to be a bushing between the shaft and the sump cover or is the casting just badly worn? Any help or advice is appreciated. Thanks...