hole

Those pesky snowblower engines usually have the big hole punched out for the 12V starter :doah: I started building an HS50 to sell and as I am putting it together the big ass hole caught my eye. So I made this cover on the fly this morning, its nothing fancy by any means but it covers the hole...

So ol' JBRocks attached his clutch brake to a 1/4" bolt which would have led to a failure one sort or another. I suggested he make a bracket to attach to the four holes that surround the PTO...BUT! JB had the side cover without those four holes. That got me to thinking! I sat down first and...

Do they make wheel bearings that fit pocket bike wheels that adapt to a 5/8 hole???

need some gearing help for 100 ft drag :thumbsup: have a 13 tooth 2 disc reaper clutch with stall set at about 3500 rpm and a 66 tooth split rear sprocket with jackshaft in between trying to figure out how to set it up to jump out of the hole and pull the whole way hitting max at the line . any...

I have this taper bore vm22 and I'm making an intake for it. My question is, should my intake flange cover this hole or leave it open to atmosphere, or does it matter? It's hard to see in the hole but it looks like it's plugged right before it gets to the idle mixture screw which is right...

This is local to me for "make an offer" and I know nothing about it. any body know what it is? looks like the bars are chrome, I thought maybe a Pinto but the fork plate doesn't look right. Also looks like a hole in the frame behind the seat ,maybe for a grab bar or something?

does anyone have a clutch side engine cover for a hs40 with only one fill hole? The one I have has 2 holes one in front the other in back. Thanks dave

The hole on top of the motor where the throttle arm is....That's a 1/4 20 self tapping screw right? What about the governor gear hole? You know behind the flywheel I just knocked it out ...is that a 1/4 20 self,tapping,screw as well?

I thought this was missing a lot of stuff When I picked it up today. I looked it over and it's not as bad as I thought. Still has the plastic chain tensioner on it. It's broken but there. When I saw the big hole in the frame with a possible missing jack shaft I panicked. If it's a sprint it's...

That's what it appears to be but the 2 bigger none threaded hole don't fit a clone.

Hi. New here and may have messed up my first post. I think I attached a photo but not sure. Anyway, I am restoring two '71 QA50's for my kids and have an issue. On the bottom side of the carb there is a tube pressed into the carb body below the float. This may be a vent but could be a plug...

Need sprocket to fit original hub & five hole brake drum to fit...

Why are there 3 holes on the governor lever? Mine came stock with the spring in the middle hole.(predator 212cc) Would putting the spring in a different hole change anything noticeably? Which hole would allow more performance? I tried searching on Google and couldn't find anything. Just curious.

So like a lot of people, I swapped the Predator 212 onto my Baja DB30. Reading on the forums, everyone said that you could reuse the back clutch cover but not the front one. So I decided to mod the existing one! First, the front cover is long so I cut a piece of it off. Then, I used the...

i have a 69730 predator that has a mild build. so far it has ARC billet flywheel ARC billet +20 rod black mamba cam header+air cleaner 22mm mikuni 26# springs and im adding a 14cc head ported and milled 65thousands 27mm intake 25mm out. stainless valves locks and retainers and chromoly...

I'm Restoring a 1970 Maverick Mini Trail and Instead of rebuilding whats left of my original seat pan it looks like a Z50 seat might fit and you can by those new. Would someone be willing to measure the width and length of the seat Pan. Also the Height of the actual seat from where the material...

looking for 6 hole sprocket spacer for manco wheel thanks Eddie

Iv been told a few things so I thought I'd ask on here before I go ahead and do it. I finally got around to swapping all my parts over to my new block rod piston flywheel all the goodies. I was gonna put a bolt and Teflon nut to plug the hole from were I removed the governor but I've been...

Hey I got a hole the size of a penny in my tire. Put the rubber patches... nope. Tried the slime/fix-a-flat... nope. Vulcanisation? (SP) Any sugestions It`s not a hole as such more of a crack like in a windshield going all the way through. Not on the sidewall thankfully.

Well like it says i'am trying to get 1 3/8 " holes in a powell swingarm . The stock arm is 1 1/2 " X 1/4" flat stock . I have welded steel to it to make it wider to handle the bigger hole . I have tried to 1 3/8 stepped bits , once i get to the 1 1/4 size the bit stops cutting . On the other...