hole

Anyone have a source for sprockets like this..... It's 60 tooth, 3/8" holes on a 2 7/8 circle, 1 3/8 center hole. I have seen them with 8 holes but not 4, or with a 2" center hole. OldMiniBikes no longer seems to carry them. Thanks!

Hi guys, I bought a new in box stock Raptor carb and I was looking at it today and noticed that it has a threaded hole in the bottom of the carb, which looks to be for if you are running a stock style Briggs air filter to put the bolt through and screw into. The problem is that I will be using...

i have a hole in my casing in the front of the motor.... i was wondering what causes a popping noise and the peice that the piston bolts onto to come flying out? i would like a reply as soon as possible.. thanks for the help

So i should've measured before ordering...but my Wards Buffalo has a 2.5" Tri bolt pattern for its brake drum. Where can I find this pattern on a brake drum?

:smile:

anyone ever have this happen? if so what was your soultion? I got a db block, everything looks to be in good shape except someone broke off an exhaust bolt and either tried to drill and tap it or use an easy out and they broke that off...it has to be one of the two because I made a jig to...

just when you think your almost done with a project :no: i started the engine right before, than the pullstart gets easy to pull and engine doesnt start i did some expecting and while i was turning the flywheel i felt air coming out by the sparkplug fml... loss of compression and not...

I have a 92 or 94 honda z50r that has a stripped spark plug hole, whats the best way to fix it?

Looking for 2 fox campus rim,must be 3 hole bolt pattern that has a bolt pattern of 3" spacing.Please let me know what you have.thanks.

Hey Fellas, I know this may be a noob question but I'm still getting the hang of small engines. I went to try and start an engine for my brother's bike. I put some gas in the tank and then the gas started squirting out a little hole in the side of the carb. :doah: Does that make any sense...

Hi all, I am new here, just picked up a rust bucket go kart for my son with a non-running Briggs 5HP motor. While I know it is not a mini bike, Google sent me here a lot when trying to find answers about this motor, so I figured y'all were the guys to ask! I am slowly working through...

i noticed it drips when i got this bike, its my flamed ram....today i rode the hell out of it and its a steady drip coming from the bottom of the tank...i know they welded it to the bracket, im guessing it put a pin hole in it...so how do you fix a leak with out destroying my paint?

Here goes.... few months back I came across a Baja warrior for 50$. Was told it just wasn't gettin spark. Bought a coil, still wouldn't start. Determined the compression was the problem. It sat for awhile and I came across a Honda gx200 for little to nothing. Wouldn't start. This motor has good...

Does Anybody know if the six hole pattern on a D/B is the same as a Disc brake on a bicycle?:shrug:....Scootercat....

Anyone know where I can get one of these? Also, I'm wondering if anyone has ever tried regrinding a worn out sprocket like this one and if so, how'd it go? Thanks!

I'm looking for a 6 hole brake drum manco #1246 I keep coming across 4 hole or even 4 or 3 hole drums. if you have one in good shape or know who sells the 6 hole let me know

Hey guys I am going crazy over here trying to figure out what size these bolt holes are on the side cover to mount my back plate on this 212 predator. from what i have narrowed down its not 6mm nor any of the 2 8mm thread patterns. now common sense would say that it has to be 7mm but trying the...

Dear OldMiniBikes members, I am currently working on fiberglass molds for thermo/vacuforming the fenders, chain guards, and cowlings needed for my Fox Campus restorations. One of the requirements is a series of .010" dia holes drilled into the molds to allow any trapped air to be drawn out. For those...

what size self tapping bolt/screw will fit in the govenor arm hole and not break it? i used the search on screws and boltsand i got torque and linkage ideas . i hate to buy 2-3 packs at the depot, they want you to buy plastic bags full. i need 1. i have instaled the flywheel ,rod, rings flat...

I did a search...and I know the hole pattern is the same as most other engines. My problem is I'm at work and want to cut down and drill out a piece of 1"x1" boxed aluminum to act as an engine riser. I don't have an engine in front of me that I can measure, but was hoping I could get this...