I'm trying to get the H25 on my Rupp Chopper running before I proceed with my build and not matter what I try it will not run off idle. It will sit there and idle all day long but the second you give it any throttle it start to pop and sputter like it's flooding and will not come out of it. If I...
I'm trying to get the H25 on my Rupp Chopper running before I proceed with my build and not matter what I try it will not run of idle. It will sit there and idle all day long but the second you give it any throttle it start to pop and sputter like it's flooding and will not come out of it. If I...
I've got one of these on a pressure washer that has lots of hours on it. I replaced the carb and the gaskets between the air filter housing and the carb and it didn't change the fast idle. I cut the throttle down and it still runs pretty fast. Wide open under a load it seems OK but take the...
Hey guys, just got my bike working again after I wrecked it, but now it idles way to high so when it's just siting there I have to hold the brake. Any ideas?
Honestly when these are new they are good for a year or so ,, Then you hope they stay running after that we have 4 of there Preditors None of them idle or run good,,, Yes Carbs are rebuilt and no change,,, Keep the Briggs Flatheads !!! They Run,,
Low Speed Jet Bored (.022) With O-rings
I am planning to buy this idle jet for a richer idle and better performance in the mid range. Anyone mess with theses? Is it worth it?
Thanks
I bought the stage 1 kit for it, so air filter and jet were replaced. The little butterfly mechanism on the carb doesn't snap shut when I let off the throttle. I disconnected the throttle line to make sure it wasn't causing it to hold the throttle open, so that's not the issue. Any ideas?
So i put the diaphragm carb back on my MTD's HS40 and got it to start with no leaks since I swapped the gasket and diaphragm. But now it'll only really stay running if i give it a lot of throttle. Ive played with the main and idle screws in and out and not much change. Its got a full tank of...
Hello,
I am pretty new to small engines and carburetors in general, so I need a little bit of help. I have a 212cc engine I got used. It was fully stock when I got it, and it's still stock with the exception of a free flowing exhaust. The problem with it is, it keeps fouling plugs.
I...
I just cleaned out and rebuilt my carburetor on my 3.5 HP Tecumseh and was wondering how to get the perfect idle tuning. It idles rough now and wants to move forward when I start it up and I have two screws with the needles on them. One is on the bottom of the carburetor's bowl and the other...
i just finished swapping a 10hp Tecumseh from a snow-blower into my go kart. i fully cleaned the carb and have the throttle hooked up to carb with out governor. it starts easy and runs great but i cant get it to idle low enough to fully release the torque converter. if i turn the stop screw down...
so i just put the OldMiniBikes hi flow intake kit on and upgraded to a 36 jet at 140 emulsion tube
now it will not idle and it doesnt rev as high, sounds like it has a rev limiter sort of noise. why is it doing this?
I have a brand new predator 212 that will start and idle, but as soon as I try to give it gas, it sputters and dies. Won't rev at all. Will just idle. Any ideas?? I can't take it back because I already removed the gas tank and air filter. Cut the wire to the oil sensor switch, and cut off the...
I have this taper bore vm22 and I'm making an intake for it. My question is, should my intake flange cover this hole or leave it open to atmosphere, or does it matter? It's hard to see in the hole but it looks like it's plugged right before it gets to the idle mixture screw which is right...
After picking up the minibike from the autozone my son started the bike up noticing that the engine is a lot more quiet. When he rode it it almost flipped him off because of the torque which took some getting used to haha. The next day he rode it to his friends house and came back and was...
Ok, Built motor changed jets adjusted needle etc... Engine starts that's Not the problem...But I have to feather the throttle to get it to pop over.........But won't idle without me,holding throttle open a bit..
my question is....Where's the Damn Idle screw,on,the carb?.....I need to set...
So I have a gx160 on my bike and just got the clutch and chain today so threw it on and the idle is too high as soon as I took the choke off it reved up and wanted to take off can't seem to find the idle adjustment on this carb
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.