intake

  1. Txpowdercoater

    Intake and Ex diff. between 3.5 and 4hp

    I'm not a tecumseh guy, I dunno why all these years I've ran Briggs...anywho, I have a few T engines around and was going to run one on a mini I'm throwing together. I happen to have a 4 horse and a 3.5 horse. I know the 4hp had a lot of blow by, I've seen it run, the 3.5 is fairly decent and...
  2. gturner598

    Intake install

    I got my intake today in the mail from OldMiniBikes. I was able to get it installed but I have no clue what am I suppose to do with that little hose that was connected to the stock air box. I tried searching and looking at pictures but couldn't find anything. Thanks. Sent from my iPhone using...
  3. Mark G

    Tecumseh Drop Slant Intake ID

    There seems to be some confusion out there about different small block Tecumseh slanted intake manifolds, hopefully theses pics will clear some of that up. Here are the three different ones that came on slanted frame motors, from left to right: H30/35(I'm not sure of the part number)...
  4. Randy

    Rupp Hustler/Scrambler wheel Hub/Brake Part HELP!

    All items found. Thanks for the help! All items found. Thanks for the help! Rupp part#18128 It holds the wheel bearing between the brake drum and backing plate. #21 on this explosion. This is the part I need.
  5. J

    WTB: Intake manifold for Briggs flathead...

    Hello, I am new here but have been into Mini Bikes for years... I need help with locating an Intake Manifold for my 475 series Briggs engine... Would like a 90 degree style to point the carb to the recoil side of the engine... Thanks in Advance, Joel
  6. W

    Dellorto intake throat length

    [/B]Need some help here.. I'm making my own intake manifold for my Del.ua19s carb. to be fitted on a newer Tec. hs50. I've got the flang, I bent the pipe. what I need to know is the proper length of the throat. Any info. is appreciated.:scooter:[/B]
  7. 6

    Slant intake for 5hp Tecumseh

    I'm looking for the slant intake that fits a Tecumseh HS50 with the squared off intake port. I know I can adapt one from an HS40, but I'd rather not.
  8. R

    wtb H30 carb and intake

    I need a carb and an intake for a Tecumseh H30. Mine has the slant intake. I could get one on ebay, but I really would like a used one so I can save some money. Please let me know if anyone has one I can buy. Thanks! Dan
  9. F

    Building intake for mikuni( how long should it be)

    I've got a 5hp Briggs, ported, header and a 24mm mikuni are in the works so far. How long should the intake and should it be at an angle down ? I'm working with a 7" 45* bend ,it can be cut Also if someone knows a good resource for timing advance keys, that would be great
  10. Scottessey

    HS40 slanted intake conversion to straight?

    Hey Fellas, I have an early 70's HS40 with a slanted intake that I'd like to use on a level engine plate bike. I had the idea of switching out the intake for a straight one. Will that work?
  11. W

    Dellorto intake manifold hs50

    Hi everyone, I'm kinda new around here. I was wondering if anyone knew where I could find a intake manifold for a ua19s that fits on a hs50? I finally bit the bullet and bought the carb. Now Blackwidow motorsports are out of them. :ohmy:Any ideas would be appreciated.
  12. trailramdan

    NEW 19mm carb, air filter and animal intake

    ALL THIS IS BRAND NEW NEVER RUN. THIS IS A FEELER THREAD. I PAID 75 BUCKS FOR ALL 3 PARTS. ID LIKE 65 SHIPPED. I THINK I MIGHT TRY MY TEC CARB AND SEE HOW MY BIKE RUNS. SO LET ME KNOW IF YOUR INTERESTED!
  13. leathernun666

    HS40 with slanted intake

    I have a nice HS40 nproject for sale with slanted intake . Carb needs rebuilt and probably a new set of points. I pulled the head off and the cylinderr wall looks great as well as everything else. No slop , looks like it was barely used. Was spray bombed, but I have started to strip and clean...
  14. trailramdan

    intake and carb ?s

    going to use intake i had i think it should work
  15. H

    Intake Manifold replacement for Z50R??

    I need a replacement carburetor for a Z50R. Problem is most of the reasonably priced replacement carburetors have a different mounting hole to hole measurement than does the z50r carb. Most are 48mm hole to hole measurement but the Z50R measurement is something like 35mm hole to hole, an 11 mm...
  16. S

    hs40 slanted intake #

    what is the number stamped on these intakes? I believe I have one but I'm really not sure, I'll check the number on mine tomorrow. I'm fairly new at this... I think these intakes are tough to get, can someone give me a general idea what these are worth. Not sure what I'm gonna do with it yet...
  17. godfather75

    wtb mikuni intake for hs50

    Can anyone make me a intake to run a mikuni on my hs50?
  18. derekbmn

    ***Tecumseh HS40 Slanted Intake ***

    Looking for a good usable slanted intake manifold for a Tec HS40. (for the old man) The cheaper the better !!! :laugh: Please PM me. Thanks in advance...:thumbsup:
  19. godfather75

    hs50 mikuni intake manifold

    Does anyone make a intake manifold for a hs50 to run a mikuni carb on it?
  20. F

    WTB: slanted intake for TEC

    looking for a slanted intake for my 3.5hp TEC engine. If you got one, shoot me a message with price and any other info. Dan
Top