needed

Just ordered the Predator 212cc engine for my El Burro. The B&S currently in it has issues. It is not the original engine, it is a 1993. I thought I should replace the Torque converter with a new one also. Can anyone recommend what might work {Comet TAV2 30 Series?} with that engine and bike...

Hello. Been looking for a kart project for awhile now, and this morning I picked up this off CL for only $30. It's complete, but needs a bit of work. I'm taking it all apart and putting it together right since it's a bit rigged. Two questions: First, anyone know what it is, or at least...

i have an old 3.5 horse tec on my ezrider minibike. my buddy made me a muffler to use on my engine. i just recently looked at it and it is cracking along the bends in the pipe. i use this bike to get back and forth to work every day. i have looked everywhere to try and find a muffler that fits...

I (we, my son and I) are new to the mini bike seen. This bike came up locally. Does anyone have any info on the bike. The owner said it is from the 60's thanks

Im looking for a few Tecumseh items for a H35-45352M I need the ringset the most. Ten over piston kit #34515 -or- 32548B piston and 28987 ringset thanks Pete

Need a complete front fork assembly, minus wheels. Anyone got any good leads re parts?

We need a Comet 20 symmetrical clutch for old kart. 6" or 7", 3/4 bore, with 3/16" key way. Thanks, Scott:thumbsup:

I need a five inch tri star or any other five inch wheel that will bolt up to an Azusa drum brake set up. Thanks!

Like its says need decals for my HM100 . I haven't seen any like the ones that were on it . Its a 1981 motor goes on a VT10 . And yes i have pics .

I could use a tire on one of my bikes that is going to Winber. I am looking for a trials or mx tread that is not dry rotted as I already have one. If you are going to the show and can bring it with you please p.m. and I can pay you at Winber. Thanks very much, Owen

I could use a tire on one of my bikes that is going to Winber. I am looking for a trials or mx tread that is not dry rotted as I already have one. If you are going to the show and can bring it with you please p.m. and I can pay you at Winber. Thanks very much, Owen

I need a 6" rear wheel with sprocket assembly.Without brake set up, I have a scrub brake on my bike.Front wheel too. I think this bike is called a "bird" Thx Mario

Guys, Im looking for a good briggs flathead crankshaft 3/4" PTO. Needs: Stubbed for starter clutch Cutout for points ignition Bushing flywheel Ballbearing PTO with OD of 1.855" I think I need part number 495645 and the bearing ill need is a 692007, correct me if im wrong. Any condition...

Parts needed: Gas cap, hand throttle, foot pegs, clutch cover, chain guard, etc. h g i l e s @ g m a i l . c o m 5 4 0 - 6 6 1 - 9 2 6 2

tc88 sorry about the typo in the title here is what i have on my rams....the green one we almost had running this weekend but the driven seems to be missing rivets. it was really loose and made the pulley egg shaped notice in the pic how the right side is bowed out. after looking at it closely...

I'm looking for a Manco Thunderbird chain guard. I believe it is model 593.

I have just purchased a Carroll Stream 5.5 hp clone-type engine. After adding oil,it fired on the first pull-very encouraging. Does anyone have any experience with these engines? They seem to be very similar,if not identical,to Lifan engines. This may be a dumb question,but could these actually...

Im working on this Comet 30 series TAV. ANd this is really my 1st time, I want to learn. It sat for over 2 yrs, and rusted on all the parts that come in contact with the belt. I ran it and the belt smoothed it out alot,quick.Here are a few pics of the driver moveable sheave, to show the rust.Its...

I'm in need of two Cat kickstands. One for my daughters 250KC and the other for my son's R2501. I'm willing to buy or trade for them. I have a couple Cat rear wheel assemblies, a 3.5hp Tecumseh power sport, Honda clone 6.5hp Homelite, ruttman 6" front wheel and a double indian head...

here are pics of the one i need....its 1 inch by about 3/4 and you can open and close it to vent the tank...i need one badly! its the last peice for my restore.