plate

So I was reading a thread on this OldMiniBikes site yesterday from fall 2014 by Matt2. I was rather disappointed that all the photo links were dead as far as his Wife's bike. Instead they were redirected to OldMiniBikes Site so I haven't a clue how this bike turned out visually speaking. As someone...

Just as the title says, looking to buy a Speedway number plate. Please let me know if you have one for sale. Thank you Mike

Ok I'm doing a restoration on a bike and I am trying to refinish all the parts. I'm stuck on my brake plates and hubs. They look about identical to rupp but they are only 20 spoke hubs so I can't just buy those shiny new ones I find online. I'm down to refinishing them but not sure how to...

Recovered Bonanza 1400/1500 seat with original BC fiberglass seat pan , both studs good. Evil Ed engine plate new for BC bikes. Seat 145.00 shipped / Engine plate 45.00 shipped lower 48. Can send pics over phone.

Looking for a speedway number plate.

Just picked up a Boonie that needs the shifter and plate. Anyone got one, anyone remaking them? I also could use the tc cover. Thanks, Kerry

looking to buy an El Tigre (bird industries) seat, and a tecumseh 3.5hp slanted intake manifold and a rupp scrambler front "racing" plate. thanks and let me know, Lyle

traded two dog house and a dewalt table saw for this and a ruttman front wheel

Just a shot in the dark seeing if anyone has a spare one laying around they wouldnt mind parting with before i pull the trigger on a new one

Hi its whizzerkid . I am looking for a number plate for a Skat Kitty it is a Tecumseh 2 1/2 hp and needs the H25 plate that gets put on the side of the cover Thanks Wayne

WANTED: Manco Streaker Front Fork Plate. Thanks, Greg

Got this in a trade deal and suspect the COBRA decal, exposed a bit from the black brushed paint with thinner, is a prior owner addition. I searched and come up with an Efenel Cobra but this looks quite different. Did run across a Sears I thought was similar but can't find it again. Came with 6"...

Hello guys,, Just built our HM60 for Nova Tote Gote and its the 1970s Block with the adjustable breaker plate,Pinging Noise, So we might have the plate to much advance on spark timing? Is this possible? We are going to Buy 90 Octane fuel today and give this Goat a ride.see if that 90 Octane fuel...

Hi Gang, I have removed the Aluminum Ser# Plate from my shroud on the 4HP TEC Used a little paint stripper an now its free from any paint. So, the question is, should I re-paint it when I paint the shroud? OR, should I Polish it and keep it bare? :glare::confused:

looking for an embossed stellar face plate :thumbsup: let me know if you have one to part with . thanks OldMiniBikes

I don't need the full kit, I have the pulleys. Need a backing plate with jackshaft that bolts to the gx200.

Switch Plate and rear fender. If it comes with the switch, super awesome.

Looking for a jackshaft mount assy for a lil indian, commonly seen on the "2 speed" small frames. I don't need the 2 speed stuff, but I will consider it if you have the whole unit and dont want to separate. I am however already pushing the envelope in the budget dept so I will simply cut the...

I'm restoring another ruttman spyder and the bike is very nice but the engine plate was pretty bad and had another plate welded on.... I know stupid right well I looked around and found a repop on OldSchoolMinibike.com wich is also ran by frank mathison sorry if I miss spelled his name. so I...

The engine plate on the Bonanza has been cut up beyond repair. If anyone has one that I could use to replace mine, let me know! Not sure if there were different sizes but I can get measurements if necessary. Thanks!