preditor

Manco gas tank (extra). Manco seat (now sissy bar). half Manco frame.

Manco gas tank (extra). Manco seat (now sissy bar). half Manco frame.

Manco gas tank (extra). Manco seat (now sissy bar). half Manco frame.

Manco gas tank (extra). Manco seat (now sissy bar). half Manco frame.

Manco gas tank (extra). Manco seat (now sissy bar). half Manco frame. Tav2 torque converter jerks and grinds when starting from dead stop.

Hi all, Wanted to share mod I did to use preditor tank in stock location with Mikuni. In order to run inline filter and ensure gravity flow I raised tank a little.

So I was reading a thread on this OldMiniBikes site yesterday from fall 2014 by Matt2. I was rather disappointed that all the photo links were dead as far as his Wife's bike. Instead they were redirected to OldMiniBikes Site so I haven't a clue how this bike turned out visually speaking. As someone...

not as bad as it seems,but you need to weld a bit.buy a motor plate with curved ends its made to do this swap,but no one says so.cut old motor plate off,weld on new one.cut a pie shape on loop that back fender bolts to and pull toward back 3 inches and weld up.now the engine fits,its a ball to...

Does anyone know the size of the half moon key on a hemi flywheel. Length and ht.

My predator 212 has so much crank end play that the flywheel fins are hitting the cover bolts. I want to replace the bearings. Does anyone know the size of bearings needed for a first generation non-hemi 212? https://www.OldMiniBikes.com/Crank-Bearing-ID-_875-OD-_2_048-Width-_500.html or...

Me again everyone,Just try to see which way I`m going to go with my warrior..should i get a Tecumseh or preditor? Which ever motor i get will be out of the box for sure..will be either an 8 or 10hp..I`m guessing..

Does anyone know if a Preditor gas tank will fit on a Honda GX160 and or a GX200? Thanks in advance. Gary M

I,ve removed the low oil shut down completely and plugged the hole with a 10 mm bolt,2 copper washers and self locking nut. can somebody tell me what the torque is for the side cover bolts ? also where i unplugged the l/o shutdown do i need to tape up the wire where it plugged in ? thanks bob

Looking for under the seat header muffler set-up. They are available new, but maybe someone has a pull off, used one for sale.

I got the 14cc head with 18lb springs, stock push rods and rockers, billet rod, billet fly wheel (stock timing), mod2 cam, UNI intake, carb jet, fuel pump ETC. My question is how much more RPM or top end (if any) am I going to see by installing 26lb springs? Also, what else should I be...

Am I the only one with a problem preditor or are there others. Hard to start, misses, poor pick up, won't stay running, starves out when excellerating. You name it. Work on it this summer and replace it with a clone next winter. That's the plan now unless I get lucky and it straightens out...

I have a new preditor which idels too fast. The TC wants to pull right on the edge. How do I adjust it down? Also missing some, replaced plug with NKG and it improved but still hear it sometimes, This engine dose not seem to run as fast top end, as another Honda clone I have. Starts easy, I have...

New Preditor (212) with an occational miss. Starts easy and idles well, but under load and especially when accelerating will miss. Tried to find a replacement plug for the Torch but could not come up with a match at FF. What are your suggestions? outdoorguy

Stuffing a 212 Preditor in a KX80 '86 frame and to do it and make it fit and feed chain onto the swing arm I have to mount it at an angle front to back. About 1 to 1 1/4" with the back being higher. How will this effect lubrication. Send picture in a minute. The plate would be level and the...

I have a TAV with a machined aluminum back plate and I think it is a TAV 30 for 9 to 18 HP. Can I use this on a stock 212 preditor. Are there any adjustments I would have to make. I could pic up a smaller tav but intended to use an open stainless steel guard where the backing plate will show and...