removing

hi I have problem removing the rear axle bolt on a mb165, it seem like mud and dirt got in it, now it seem it all rusted and stuck, I have try using wd40 hammering the bolt but it doesn't move, it the long bolt that hold the rear wheel on, do anyone have another sugguestion?

hi I have problem removing the rear axle bolt on a mb165, it seem like mud and dirt got in it, now it seem it all rusted and stuck, I have try using wd40 hammering the bolt but it doesn't move, it the long bolt that hold the rear wheel on, do anyone have another sugguestion?

News-Flash!!!! ...Getting ready to ship this Bonanza 1300 frame to Smallbore ..the jackshaft bearing were toast so I decided to take them out (save on shipping weight :laugh:) and use the opportunuty to show Kk jr. a trick or two. Of course this may be old hat for the seasoned...

Today I started restoring my old Manco. I'll post pics in the project section soon. I bought some paint stripper, and it took the majority of the paint off with a scraper. Then I took it to the car wash and sprayed it off. Now I'm using a wire wheel with a drill to remove the rest of the paint...

I have an old Tec 5hp (not sure of the model off hand). The question I have is what is the trick to getting the carb off. There is a spacer between the carb and block, with two screws holding it to the carb and two holding it to the engine. The screw heads are partially covered by the carb and...

Every time I try to do this I have a problem. The bead is always STUCK.. Today I had a bright Idea:out: !!!! Take The wheel and soak it in the kitchen sink in boiling hot water. Add tons of dish soap. ( Maybe should get permission from wife first ). Let it soak for about 1/2 hour, rotating...

Unfortunately, I don't have a valve spring compressor anymore, and I was wondering if there is an easy way to remove them without the compressor tool? :shrug:

I have a Heald Super Bronc that someone painted the whole thing a dark green. I want to bring it back to original red and chrome. What's the best way to get the paint off the chrome fenders and handle bars? Thanks

Does any one have any tricks on removing brake drums from axles? Been heating and prying with no sucsess, same with an axle hub heating and pulling no luck. Thanks

Is there a special tool I need to remove a clutch? Thanks, Liam

started working on my cat400x today. need a better idea to remove the carlisle tire off the rear rim. i tried using screwdriver to get over the rim but its taking forever!! any faster way to remove these old tires?? hate to cut it off if cant..

Hey guys I'm new, not sure if there is a questions page on this but I'm having trouble removing the fan off my 5hp Briggs and Stratton engine. I have the correct puller, removed the set screws, but It bends the Iron on the fan when you tighten the puller. It's not totally rusted, more of a light...

THIS JUST CAME BACK TO ME TODAY WHEN I USED TO RACE AND NEED TO REMOVE LETTERING FROM THE CAR I USED OVEN CLEANER .SO TODAY I NEED TO CLEAN THE TANKS I GOT THIS WEEK BEFORE PUTTING THEM UP SO I GOT A CAN OF OVEN CLEANER PUT THE TANKS IN A BIG PAN NOT EVEN A FULL CAN WAS USED ,I WAITED ABOUT...

I have some steel parts that have been bead blasted and coated with a silicone spray made by the Liquid Wrench company. Now that it's time for paint; I want to remove the silicone. I talked to the laboratory people at the Liquid Wrench company and was told that "You could probably try mineral...

or by engine number? its an hm100. just kinda want to know what i have a little better. i kind of think its a cid but im not sure, any guidance would be much appreciated.

How do I go about getting the wheels off the axle? Doesn't seem to have been off for quite some time. I don't want to mess up the wheels, and they are stuck good. I am soaking them down with some Kearney Rust Cutter. It took 3 days of spraying and soaking to get the axle nuts off. Would any...

Get out of my thread

Any one have a secret weapon for removing a clutch? The clutch is installed sprocket out and one of the set screws just will not break free. I broke one hex key trying to get it to break free. I have been putting penetrating oil on it and still won't budge.

I've got a brand new HF 6.5 clone and I want to install a chain guard bracket. Can I get away with removing the top two crank case bolts and re-torq without replacing a gasket? Thanks folks.

Does any one know how to remove the lower portion of the fork on a 675? I pull the living hell out of it on my vice, hammer on it and it will not come out for anything, they must have been pressed in there really good. Its driving me nuts!! I need to replace the springs on my forks. Any...