setup

Hello all I have a 6hp Tecumseh and I would like to put a 22mm mikuni Carb on it.where can I buy the intake for the Carb setup any help is appreciated thanks all.

I recently purchased a B&S 5hp flat head and it came with a different carb setup. I would like to replace it with the stock setup that has the fuel tank under it. I have searched and searched with nothing found. There were a few on eBay and they looked as if they were sitting in salt water for...

Does anyone here know anything about this kart? I need information about the intake setup and the engine mounts. Thanks Brad

I just picked up a Wards T555 this weekend and have some questions on the TAV setup. I've got the driver and driven units but it didn't come with a belt. It has slots for motor location adjustment, so the center to center on this setup is variable. However, there is a set of mounting holes in...

Hello, sort of an introduction here with my first question. I have belt-drive go-kart configuration with a 5HP Briggs and Stratton horizontal shaft engine, carb on tank. S/N 135202 for those who really know their stuff. It was taken off a power washer and installed by the previous owner...

Found this estate sale Rupp with a hideous and blown Briggs and Stratton setup. It also had a smaller mag style rear wheel.

Looking for parts to build a trike. I have the front fork and some steel but I'm missing A LOT! I would like to have a live axle. A complete axle with wheels, sprocket, hubs, etc would be awesome I need a brake setup I need a front wheel for a mini bike ( my fork is from a mini bike...

Hey Ya'll~ Rookie Marc here with a couple brake, seat and suspension questions. I've searched the old posts and many of the topics were very helpful, but a few questions still remain. After ordering 6" Astro wheel setup and Hilliard 3/4" 12t clutch and 60 t sprocket, Im still a little...

can yall post pics of how you are running your chain and what your using on your db30 ? thanks

I am working on building a motorized drift trike and have a few questions about a live axle set up. I have a rear frame section from a kart and the 1" axle, when I got it somebody had already taken it all apart. I have ordered all new parts but then seen a picture of another motorized drift...

briggs & stratton 5hp throttle linkage governor setup carburetor stock 4

briggs & stratton 5hp throttle linkage governor setup carburetor stock 3

briggs & stratton 5hp throttle linkage governor setup carburetor stock 2

briggs & stratton 5hp throttle linkage governor setup carburetor stock

i want to build a really fast bike to do alot of cruising with. i have a new "old style" 212cc predator to use. i need suggestion on whats the BEST setup for a really fast cruising minibike. thanks

how does this setup for a predator 212cc sound like it would work. -24mm mikuni -billet flywheel -billet rod 3.595 -wiseco 2.756 flat top -dyno 308 cam -14cc cylinder head big valve, milled .065, 26lb springs,27mm intake, 25mm exhaust -arc billet side cover -catch can push rod= idk...

Ok so I want to put a tav on my predator but I want to still have good top speed does anyone know a way that I can do that I know there is a member on her that has a bike that has a tav and it hits 80 Also I you guys need to know here is why my motor has 18lb springs 22mikuni Header...

Hi all , I'm in the process of building a mini for my 7 year old daughter. I've put a 2.5hp engine in and lowered the seat a bit for her. Next on the list s brakes. The problem I have is the bike has a cable operated drum brake , for one it,s to far for her little hand to reach and even if...

What do you guys think the best gearing setup is the motor is a gx200 clone (the good clone square gastank) and it has a pipe,airfilter,18lb springs and some carb work what gearing setup would be best for me in the 1/8th, the bike is a ruttman spyder, the current setup is 62/12, I'm looking to...

Just my take on the dirt bug jackshaft, using a Comet back plate that didn't end up being used for our go kart. Used the angled holes to clear the muffler, but had to raise the engine up with a piece of 1/4 aluminum I had. Just so the back plate wouldn't hit the motor mount plate. Have a 22...