Please excuse my ignorance on this, but I'm a first time mini bike builder, and I don't understand how you determine which size wheel to get. What are the factors you determine in choosing a wheel size? I guess I understand the tire needs to match the wheel size..same as a car. Then does the...
Great news Taco lovers !!!!!!! ....are you tired of those buzz saw used sprockets.....after years of R and D the new 60th Taco sprocket is done and ready to sell....thanks to Joe Rivello at Taco mini bike soon more parts and frames will be out.....they run about $70 plus shipping ....I saw a few...
It appears that the typical mini bike uses #35 chain and sprockets but is limited on the sprocket size. I don't see them being less than 60 teeth. Clutch sprockets are like 12, 13 teeth etc. This seems to practical for most 3.5 HP engines.
Would that be a reason to go with a #40 / 41...
Boonie jackshaft mounting plate with nice jackshaft and newer sprockets. Mounting plate is original. Sprockets and shafts is not. Single speed setup. Good parts. $60 shipped. I can email or text photos. Located in west michigan.
I have a 6.5hp motor piped and air cleaner and 12 tooth front and 60 back for sprockets and my clutch started messing up and was wondering whats the best clutch to get
I have taken a picture of the underside of my minibike. The sprockets on the jackshaft are both 15 teeth. The distance between the tipss of the teeth and the shaft of the swing-arm is only about 1/4". Is this normal? Or should the sprocket on the engine driveshaft side have fewer teeth so that...
As stated, new set of 6" Azusalite wheels with new/used drum sprockets both 60 and 70 tooth and an Azusa brake backing plate assembly. Tires are tough to mount on these wheels but with silicone spray it's easier, Asusa sprockets often need to be trued so I make no guarantees on the straightness...
ok I have a live axe Murray explorer. when the kids take off I hear this loud pop. there is no way that I can see to adjust the slack out of the chain. the axle is fixed. the secondary drive shaft is fixed. there is no way to move either sprockets forward or back. but I have about two inches of...
Since I am no longer using the jack shaft and never will I figure someone on here may have a use for it. It is the complete jackshaft with sprockets and original chains. The large sprocket chain will need a master link.
Video of it
5wx2Bh-5FMw
$50+shipping
I may be parting...
Two chrome Ruttman sprockets for sale.
One really nice, one ok with a couple extra drill holes.
$30 for both, shipping included.
Must buy both at this price. Will not separate.
PayPal only.
Dave rom Salkum, WA
Made a deal to rebuild a bonanza and i get the go cart. Did not know what I was getting into. Working on identification now. I think is a BC 1000. Trying to figure out the wheel mfg so I can find rear brake and sprockets. The front end has sliding fork suspension, headlight...
I have two Ruttman chrome sprockets for sale.
One is in good shape with some fine scratches and a couple small chips around the bearing hole. $50 plus shipping
The second one has a few extra mounting holes drilled in it. Chrome is scratched and far from perfect, but would still look...
Does anyone know if there is a company that makes aluminum rear sprockets for a Rupp roadster or roadster II? Seems to me it could really clean up the look on the rear wheel area.
Dave
I have 3 Martin sprockets. 2 of them are chain size #40, and one is #41. All of them have 13 teeth, and are 7/8" wide with a 1" bore with a 1/4" keyway.
The two #40 are older, but are in good shape - just some surface rust. Set screws are missing. Martin Part #40BS13 1
The #41 is barely...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.