Hard to find Tecumseh steel Half Tank used on some early mini bikes. This one is super clean inside and out with just a few very slight dings. Threads are also nice. Includes mounting bracket and vintage vented steel cap. Ready for paint!
$60 shipped...Paypal only.
Not sure the brand of it or bike it came from, but the sprocket is perfect! For a 6" tire, 60t 35 pitch and its clean and straight. looks like it may have a had a disc brake but there is not wear in or chain rash or anything like that, face of the sprocket is clean. wheel has some light pit...
Hi,
I recently picked up a late 60's Lil Indian roller. It has 5" steel wheels on it but in searching I could not find any reference to 5" wheels. Are the 4" steel wheels original?
Thank you!
Dante
Hi guys, Anyone have any knowledge of the 6" steel rim posted on the OldMiniBikes warehouse site product #AZ1025 that comes with a 3/4" bearing? What I'm trying to find out is what bearing is needed to change it to a 5/8" ID bearing to suit the axle before I order it so they can be ordered at the same...
Pics tomorrow but I have a good Comet stamped steel TAV backing plate (no cover) with a 20 series comet asymmetrical driven 40-41 tooth unit in good condition. Will take $90 delivered anywhere in the lower 48 but will consider Canadian shipping however you Northerners know it's twice what US...
have some wheels for sale :thumbsup: 1 set of cat wheels 6" with 68 tooth sprocket and a decent carlisle double indian head (no stars) $60 shipped 2 set of general tire and rubber co. 6" split steel wheels $55 shipped 3 5" manco wheel needs a good cleaning $25 shipped 4 unknown 4" split steel...
I'm trying to get a verification if these were the steel wheels that L I used on the Carlisle tired pre mag wheel bikes. I'm looking at pics and its really hard to find any close ups. And were they the same front/rear. Far as knew they were always spacers off the wheel bolts but I think a saw...
Looking for a plain steel mount for Westbend 580/700. The mount I'm looking for has a lip rolled up on one edge.
From what I can tell this was an early stock mount, not aftermarket or racing stuff so it might be found on some industrial application engines.
Cash or trade...Send PM please...
Howdy,We just replaced all 52 steering bearings in the front handle bar/goose neck area.. Does anyone know how these should be adjusted properly ?? 5/32" bicycle bearings steel chrome.. Any help great appreciated.. Thank you, Marilyn.. :hammer:
Been working for a week now and just about done with it . It will hold my Hobert 140 mig and my new Eastwood AC- DC tig welder .
Also will hold two bottles, 100 percent argon and the 72-25 for the mig . Still have two finish the cable holders , the flat steel loops on the legs will have 1/4...
I can't remember what this came off of, I think it was a tecumseh. I'm a bit of a tank hoarder so they all blend together...
Its about 3" wide, 3" tall, and just under 7" long. Filler is in the center and the drain is offset to one side. Tanks is nearly spotless inside.
Asking $25...
I've stripped this here Stellar down to it's naked steel frame and want to make sure I prepare the metal for painting correctly. The old paint was quite bumpy and whatnot. Wanted a nice smooth finish.
What have some of you used in the past to get it all squeeky clean and oil free? Looks...
Have a pair of Lil Indian (I think) 4" steel wheels and sprocket. Rear wheel is pitted pretty bad but could be glazed and sanded. Sprocket is nice as well as front wheel. $50 for all of it. I can remove the tires for shipping. Paypal only please..
Sent from my Texas Instruments Speak and...
6" Steel Cat wheel nice outsides, inside has rust from tire being mounted. Please see photos for condition. No hardware or stars
$65 shipped - Paypal - Wisconsin
Have this left over from a previous build. Double indianhead sawtooth. Has a crack around the seam on both sidewalls. Wheel is solid. $15 plus shipping...
Hi, selling my Doodles metal fenders. Currently Rustoleum metallic blue over the factory red. Front fender is straight, just has a couple paint chips. Rear fender had a small dent that I tapped out, and the very edge of the rear was repaired from a wheelie incident involving the previous...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.