stock

Absolutely perfect, mint NOS condition. Campus F/X, Doodlebug, Trail Tramp, etc. Excellent crisp detail, and the adhesive is still good! Available elsewhere for a lot more. $25 bucks shipped, paypal only please. Price is for a pair.

Looking.. Thanks.

Hi all! I am in the process of getting my Baja mini bike back up and running. I have received my new carburetor and put it on the bike. Unfortunately during disassembly I wasn't very smart and forgot to get good photos of the throttle setup. Below are the photos I do have. I am...

New Old Stock rear fender for Speedway bikes, not sure of the models it fits. I'm assuming 10" wheeled bikes but I'm no expert. Measures roughly 16 1/2" long by 3 3/4" wide. Not perfect, but I'd call it a strong 9 1/2 out of ten. $45 bucks shipped, I have a couple of these. Paypal only please.

Brand New Old Stock, genuine Fox foot peg rubber set. Not reproduction!! Fits 7/8" bars. Perfect new condition, a little dusty from storage. This is for the rubbers only. They are available "elsewhere" for over $38 bucks. My price is $25 bucks shipped, paypal only please. I have...

Brand New Old Stock Fox grip set. A little dusty from storage. For 7/8" bars, throttle side comes with plastic tube. These grips were used on many Fox spoked wheel minibikes, I have also seen them on Colemans, MTD's and others. These are available "elsewhere" for over $38...

Universal Comet two speed set up, had for many many years. Comes with Jackshaft hangers (not pictured) NOS, but has very minor surface rust. $140 , Paypal only please.

So I was looking at engines for sale and saw this. Would this be a good starting point for a raptor engine? Are these good engines?

I ripped apart what I believe is a h25 and found something's that don't look stock. Like everything. Retainers, piston and rod, cam? It has an oil pump setup to lube the journey's where the cam sits on the side cover. Studs in block to bolt down head. Rod bearings. Looks like someone tried to...

Bought 1.3 rockers and didnt get plate for it cuz affordablegokarts said you could modify stock plate....... what is the mod I have to do?..... Cut out the slots where rods go? Idk

Not mine New old stock Tecumseh H5 engine Old New Stock. Brand new never been started 5 HP Tecumseh. Fits many older applications, finish that restoration project with a brand new engine made in USA. $350 OBO.

Ok. First the exhaust. I have this welded up header that allows for a muffler to be put on. How much difference if any from the shiny header will there be. Both with the muffler screwed in and without. Second.after putting the fuel pump on yesterday. I came out today and there was a gas leak...

Bought a new one and finally put it on something, and it leaks 360 degrees around the seam of the tank! Nice quality control! I have to say it did start on the second pull though and does run well. What can I expect for 98.00 or less right? Anyone got a take off to sell? I have the black...

I believe it would be 10.5.1 compression would it be okay to run pump gas? Can I run 89 or what should I RUN? Thanks

I need some direction in adjusting the governor on a DB30. I know how to adjust the spring between the throttle linkage and the governor arm, but that's not my issue. I took some stuff apart to get things cleaned up a little bit and I think I may have messed something up. I removed the...

Hi all. Just picked up a db30 straight frame and the rear wheel has quite a bit of wobble to it. It's also missing the chain guards too which seem impossible to locate for the older model. Anyone have anything laying around??

So I bought a new throttle cable, throttle return spring and brakes for my son's new Doodle. He's really into it. Awesome. :) Now eventually I am going to upgrade the motor and stuff to get him going faster and have more fun, but for now during his learning experience I'm going to keep it stock...

all these parts are brand new never used bsp 3 cam 20 bucks complete cylinder head with valves and extra springs 40 bucks race ready carb 25bucks billet air filter adaptor 15 bucks

Without the fan shroud how do you tell them apart? What do have to look for since most shrouds interchangeable?

I can't seem to find the lack Mamba Jr Cam & 26LB springs in stock for the Hemi motor. Any idea where I might find one?