Hey guys.new to site and getting into tinkering with my new pred 212cc motor on my motovox(?) frame. Just curious to what size carb is on this motor. I believe it's a new style hemi head ( cast valve cover, saw pic here onsite ) want to know if I can transplant any carbs to it. Thanks for...
I would like to buy a camshaft from a stock doodlebug engine. Doesnt matter if its used, just needs to be in good condition. Please post pics and let me know what you want for it. Shipping is to 17042. Thanks.
I took this out this morning and was going to start to enlarge it, but I cannot find my welding tip cleaner. I will pick up another set today. Might swing by the hobby shop and see if they have small drills. Mine dont go that small.
I will take some pictures today.
Dave
Hello all.
I am in need of the top plate and stock throttle linkage for a Honda GX160/200 motor. I need the plate, throttle arm, the washer, spring, rod, and nut. Dont need any of the governor linkage or arms.
PM me what you have.
Hi everyone;
I'm trying to find out the size of the bolt to keep the stock clutch on the shaft of a stock 2.8hp 97cc Doodlebug. My lad lost his in the grass when his dad didn't threadlock it in place. ;)
Is it a 5/16"-24 x 3/4" bolt plus the washer and lock washer as OldMiniBikes suggests...
Hi. I'm piecing together a custom build that started out as a Manco Thunderbird. It will be unrecognizable when I'm finished.
I would like to post pictures in this message box but I'm not able to. I uploaded 5 pics to my attachment but they do not do justice.
I paid my $25 to upload more...
I have a stock db30 engine (98cc Lifan flathead) that I would like to extend the intake on. I'm wondering if anyone knows where I can get a flanged elbow that will fit the intake on this engine, which I can use between the carb and the engine. There are several reasons I want to do this. One...
Honda/Clone valve retainers to use 26lbs springs on stock valves. 20$ plus shipping. About 1 hrs run time on 18lbs springs. Paypal. Shipping from 10509 should be only couple bucks to anywhere.
I have another predator 212 sitting, after helping a friend work on his car... apparently he thinks i like these motors! lol... am going to play with it at a later time...
anyhow... i have to put together the hemi shortblock i have and send it to a friend out of state and needed a head for...
How will timing affect a predator with a rejetted carb, filter and pipe? I am confused as to what timing does on a stock motor like this.
I have read that it can increase low end torque and then other posts that it moves the torque more to the top end. Which one is it?
I am looking for low...
wanted new or used stock muffler from gx390 gx340 or clone
I need one because I need a compact design
.
thanks for any help this is for my buildoff project
thanks again
Hello all. I'm new to the site, new to mini bikes and new to working on any kind of motor. Recently purchased a motovox mbx10, replaced the motor with a predator 212, and added a header, intake kit and jets. The problem I'm having is removing the stock emulsion tube. I've removed the stock jet...
I'm ready for some more power on my 212 Predator. I was curious of the maximum valve size that could be run with the stock 2.756 bore? In other words how big of a valve can I physically fit using the stock bore? thanks in advance.
I'm curious. My billet flywheel is supposed to be 25 deg BTDC.. with an auxilliary slot for 30.. What is the stock flywheel ign timing? Curious as to how much advance this wheel puts on the engine..
Also, anyone know the weight difference between genunine Honda 200 & a clone (Kohler), if any...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.