stratton

These engines are just cool. 1932 Briggs & Stratton Model "A" 1920 Briggs & Stratton PB Moto Mower

For that Die Hard Briggs Guy ! Briggs and Statton parts lot

I need 2 Briggs 3 hp cyl heads (080202) the 2 1/2hp would also work (060202) complete with head bolts would be great ....pay pal ready ....Thanks

OK now is the time to sell this never used motor, it was bought for a Go Kart originally but I tried to set it up for use in a mini bike and as we know life changes and we have to adapt. I pulled off the linkage and the tank to fit the engine into a frame and I was going to use a slide carb...

I have a question hopefully one of you can answer for me, I have an old flathead briggs 7hp, that came in my tote gote, from googling I believe its a 170000 series?, Its missing the shroud and pull cord assembly. my question, does the shroud have to come from a 7hp briggs or are there others...

This engine is a syncro driving a power washer. Its set up to run at 3600rpm. How do I get it to idle and how do I set you a cable operated throttle?

So I just bought a 68 Briggs, supposedly 5hp. The model number is 100202 0015-01 6809107. Bought it for $35 dollars and it runs, but is missing a few things. The other motor I didn't buy I got for free . It is a 63 model number is 100202 40117 6305291 that is a 4hp. By looking at the motors I...

Hope this is allowed. Selling this Neon Briggs and Stratton sign here before ebay,as I would like to see a member get it before EBAY. The switch is broke,so plug it in for a bit,then unplug and plug back in to reset ballast then works fine.Or resoulder a switch back in. I am asking...

Dont know what section to offer a Briggs and Stratton neon.Would like to see it go to someone here before i put it on ebay. So if a Moderator could tell me what section to list it. Thanks

trying to figure out what I have. no numbers anywhere on the engine.TIA, Lyle

This is a fall/winter project me and my brother made. Its a fully homemade frame with front shocks of a Kawasaki 250 i think, rear shocks from Beverly 250, front wheels of a Suzuki Alto 1.0 (Suzuki also donated an alternator). Engine is a Briggs 8HP flathead with a carburetor from a 12.5HP flat...

Hello, im new to this forum, and 4 strokes. Know the basics, how it works, what can go wrong, how to tune it and port & polish shit. Know alot about 2 strokes and porting on them and about carbs. My brother is convincing me that a 27mm Jieli carb is NOT needed on a 5HP, not even on a 8HP wich...

Got to clear some of the clutter...... Pulled this off a hardly used/garaged (Low Hours), Grass edger. Sitting on my shelf for 10+ years. 3/4 keyed shaft 1 1/2 inches long. Still had original spark plug. New spark plug, changed oil and new air filter and it started right up. Probably going...

I have a 3hp B&S motor i'm trying to put back together but can't figure out the springs on the throttle body. In the picture i've attached, you can see the spring on the top of the engine and where I think it is supposed to go. The right side of the spring was connected to where the arrow is...

Can someone tell me the year a hp on this little Briggs engine ? Model 92502 Type 3105 01 Code 85020706 :rolleyes:

Restoring a Sidekick and I would like to put a period engine on it. I am looking for a 3 or 4 HP Briggs and Stratton engine between the years 1960-63. Thanks

R Tek Engine for Toro CCR2450 CCR3650 Powerclear Lawnboy Insight | eBay This the only 2 stroke that I know of which B&S made. It was produced for a Toro snow-thrower. The engine appears to be ~5HP with a 3/4" keyed shaft. Might make a nice power-plant for a mini-bike. The ebay listing does...

I need a seven or 8 hp Briggs & Stratton with a crankshaft 2 3/4" long by 1" in diameter. In good running order. For a tote goat project.

Very Clean 1976 Briggs & Stratton 2HP Engine White engine - Model 60102-0303-01 76111501 Built November 15th 1976 Complete engine with Carb,Gas tank and exhaust Can send additional pics per request $50 Plus Shipping or Local Pickup Good compression & Spark

Picked this up thinking i was going to put it on something. Very strong 1953 Briggs & Stratton 9Hp Flathead Model 14 Type No. 202051 Vin # 345496 Build Date; December -1953 Bore 2.625 L-Head $100.00 Local pickup Will Ship on buyers dollar Can"t load pics I picked this up 6 Months...