stripped

I picked up a cheap $200 baja mb165, he said the engine just needed a tune up. The bike was in bad shape, but I was going to strip it down in parts and hide them in a cabinet from my wife. I Decided to donate a rebuilt MB165 mini bike to a family we know that the two boys father was a...

Hello everyone, long time lurker, first time poster. Lots of good information and people to be found here :) Please bear with me if I refer to anything with the incorrect names/terminology, I'm a newbie when it comes to this stuff, but I'm here to learn! Well, I purchased a "home made"...

anyone here interested in doing a chainsaw-go kart motor conversion? I know I need intake, carb etc, but that's about all I know when it comes to 2 cycle motors, I would send saw motor stripped down and purchase parts needed of course I will pay $$ thanks the saw I have is an older...

Built this bike last year for the 50cc fun run in Suches Georgia in October. Could only get it in primer for the run. Ran like a top with no problems. Motor was stripped down and has new bearings, seals, piston, rings, special cut rotary valve. And repaired kick start. When I returned I stripped...

Hello everyone. I am finally getting around to working on this bike I picked up last summer. It's a '69 Taco T100 with the trail tamer front end. I did some frame repairs and I have all of the paint stripped off so I'm trying to decide what color to paint it.I am wondering if any of you Taco...

Up for sale is a broncco tx gas tank. Minor surface rust. 2 small dents in the front. Needs to be stripped. No holes. Inside looks clean. Asking $75 plus shipping.

I stripped out the set screw hole on my clutch, the one that screws into the key, the other set screw is in nice and tight, is this set screw that important, once I screw in the bolt at the end of the shaft, the clutch won't be able to slide off. Do I need to re-tap the set screw hole or do you...

just when you think your almost done with a project :no: i started the engine right before, than the pullstart gets easy to pull and engine doesnt start i did some expecting and while i was turning the flywheel i felt air coming out by the sparkplug fml... loss of compression and not...

I have a 92 or 94 honda z50r that has a stripped spark plug hole, whats the best way to fix it?

Hi all. This is my first post here, so thanks for having me. I bought a doodlebug off Craigslist for $30. I thought it would be a nice project for me and my son. I noticed the mixture screw on the side of the carb is stripped out. Like a lot of other folks here, the motor will not run with...

I bought a 3hp Briggs motor a few months back for $12.50, the exhasut port threads that you screw the muffler into where mildly worn allowing the muffler to loosen up while running the engine. I tried a jam nut in the end of the muffler but it still won`t work. This brings me to my question...

rats stripped my jet. i have no luck i took my time worked clean but it didn't go well. i took the carb off got a new screwdriver and chewed it up. it would not come out. well i drilled it like it was cleaned it the best i could. then i blasted around the block. i did a #64 bit i dont want to...

well i guess its a good thing i decided to take apart my 8hp briggs before running in the plastic gov gear is stripped out and the cap to hold it down is chewed up and in about 100 peices. this is the secound 8hp briggs i got with the same prob. is this just something with the 8s or did someone...

Lil Indian 450 1970 Frame Repaired & Stripped

So after replacing my sparkplug bike was running choppy so I decide to gap it. A few more days later same problem, I took the plug out to check it re- gapped it and tried to put it back in no dice... I kept twisting and turning no luck So is there a way to fix this should I try a different...

so where do i start... if you clicked on this thread your probably a sicko, or you got the humor. i bought this bike a little while ago, unfortunately i did not know i would be making a post but since ive decided to make a project log im posting pictures. i did find some pictures if...

ok I got a problem here, I made a custom exhaust and in the process of putting it on and taking it off I stripped the exhaust bolt holes really badly. any advice? and no the port itself isn't threaded either. the engine is a 5hp briggs I/C flathead