tube

  1. MCF2891

    WTB: 410/350X5 Tire and L Stem Tube

    Looking to buy 410/350x5 tire and L stem tube that is in good shape with a good amount of tread left. Looking for a rounded tire like the CST knobby tire.
  2. Ajf

    Rupp 1970 up rear lower shock tube

    I need 1 rupp shock or just the lower black tube. I need to replace one that has a twisted eyelet and chain rash. I need at least the tube to be in good condition. Thanks
  3. Stangrcr1

    Pulsajet pickup tube

    Pulled the carb apart for the Christmas Trike, and it is in good condition except for the pickup screen being plugged. This one has one long brass tube, and then a small screen fitting on the end. It is not like the newer ones with the long plastic pickup. I looked on Partstree, and they show...
  4. massacre

    ARCO Head Tube Bushings

    Hello, I need some ARCO head tube bushings bad. Will pay good money thanks! These seem like steel but would prefer bronze but will take whatever I can get at this point lol 5/8" ID X .965" OD X 3/4" long Flange = 5/64" thick, 1-1/8" diameter Thanks for any info anyone could provide...
  5. massacre

    Head Tube Bushings ARCO

    Hello, I have an ARCO that has bad bushings in the head tube. The forks have a little shimmy in them, and when I removed the fork bolt (brand new) it was worn all funny on one end of the fork bolt. Does anyone have a source for new bushings? They seem to be bronze. Thanks for any info you...
  6. B

    can i use inline fuel filter on valve cover tube

    i can or no please help
  7. jeep2003

    Inner tube valve stem Fix

    So on my trike the valve stem ripped out of the tube. It was a larin. Rather than buy a new tube I thought maybe it can fix. All I did was put a washer on the stem. it had a rubber coating on one side to seal against the bottom lip of the stem. It came with a bolt together fiberglass bath tub...
  8. Danny01

    Oil drain tube and valve?

    I was wondering when I have to change the oil in my go kart its in a tight spot, so is there any way I can get rid of the drain plug and attach a tube on it with a small valve? Also when do I change my oil, I will be using it in the winter so before?
  9. D

    6" Azusa wheel and tire wanted

    I need a 6" Azusa wheel and a good quality tire. I have a 5inch currently and can't keep tube in it.
  10. Shawnster

    Any Musicians here?

    Hello all, I was just curious to see if there any fellow musicians here. I am guitarist / bassist. I started playing guitar back when I was 10 back in 82 when I got my first nice acoustic guitar and learned my first three chords. Since then I have been hooked! I am mostly into rock, southern &...
  11. S

    largest emulsion tube causing bogging down, how can I fix?

    I installed a predator 212 on a go kart project I'm working on and I got a stage one upgrade kit which includes 36 & 37 jets and a larger emulsion tube, when I installed the air filter kit it was so lean it wouldn't start so i swapped in the 36 jet and it ran good, then I swapped in the larger...
  12. markus

    NOS goodyear studded 6" tires 4.10

    Goodyear "studded" tires 4.10-6" these are NOS never used or installed, these are rated tubeless so for bikes like the arco, birds, and various department store bikes with the 6" one piece wheels these can be run without fighting with a tube!!! And Many of them actually came with this...
  13. xr7gt

    1970 Taco 22

    70P114 Complete with replacement 3.5 engine. Crusty paint. Original seat. Forks have been welded above spring on driver's side tube. Jackshaft sprockets and wheels move freely $250 or best offer 951 751 7232 Pick up or i will work with you to have it Shipped out at your expense.
  14. Not so mini bike

    Roper guys

    I've seen a bunch of roper builds on here and was wondering where you guys got the bushings for the forks and neck tube. I believe they are 3/4" by 5/8".
  15. R

    problem with removing tire from rim halves.

    Why is it such a pain to get the haves of a two piece rim off the tire on a mini bike? In the process of mounting a new tire on a new rim I put hole in the tube so now I need to get the rim halves off the tire to put in a new tube and it is proving to be almost impossible. Before mounting...
  16. Not so mini bike

    Bronco tx parts

    I have front brake rotor painted green on one side. I believe I have the original screws to mount. One foot peg Jack shaft with sprockets. Front and rear axles with spacers and adjusters. 2 front tube caps. Green over spary but will come off and aren't damaged. $35 shipped for...
  17. Dan-E-boy

    HS40 slant engine parts. taylor muffler, intake, oil dip stick and tube..

    Up for sale is everything you need to turn your HS 40 into a slant mount engine. The taylor model 100 exhaust , slant intake, oil tube with dip stick and the governor arm. Asking 125 for everything shipped. Won't separate sorry. I added a pic of them on an engine. Thanks for looking.
  18. Tom S.

    You Tube Links Don't Work?

    More often than not, when I click on the link to a You Tube vid that someone has posted, I'm just directed to a blank page that has "<object%20width" in the address bar. Whyzat???
  19. J

    HELP CARB TROUBLE 168f 6.5HP

    so i just put the OldMiniBikes hi flow intake kit on and upgraded to a 36 jet at 140 emulsion tube now it will not idle and it doesnt rev as high, sounds like it has a rev limiter sort of noise. why is it doing this?
  20. Sixpac440

    Front Tire for a Heathkit Hilltopper, advice? ... do you speak German?

    My Hilltopper's front tire is splitting on the sidewall. This bike is a driver and I am concerned with a blowout. Does it look to far gone to use a tube? The bike is very original and I would like to keep the same tread pattern if I get a new tire. I found a tire that looks to be a...
Top