Search results

Are these front shocks rebuildable and any idea where to get replacement seals as well as how to disassemble/reassemble them? Also, I see some grind marks on them - did someone remove the front fender mounts? Thanks

Anyone bought or have any experience with these? It looks like it has the hemi head and not sure if its based off the VC 460? Thanks https://www.harborfreight.com/158-hp-459cc-max-performance-ohv-horizontal-shaft-gas-engine-epa-58383.html

Wanted to get your all's thoughts on these. They seem to have pretty good reviews. Thanks

Anyone have a picture of this bike in use or out of its container? https://www.facebook.com/caf.wing/photos/a.1094948907209950/5912756692095790/

Sounds like some golf courses are using something like this. Looks like the fat tire 2-wheeler would be a lot of fun vs. the standard golf cart. https://golfstead.com/best-electric-golf-scooters

Comet driver 94C 1” bore, driven 90D ¾” bore. In 2019 the driver cost $199.50 and the driven was $186.50 less shipping and tax. Installed in the driven is a reverse (blue) spring for use as outboard installed and includes the original (brown) spring for inboard installed. Included are some...

I picked up a 80ish Honda XL125S with no motor and wondering if I can add a newer 125cc without many modifications. I now the 80s XLs were 6 volt and I am assuming the new 125cc are 12volt. Anyone done a swap like this? Thanks...

Pray everyone has a great day with the family.

Anyone have any ideas where I can find front shock repair kits and what oil should be put in them. One of the shocks is seeping some from the seal. Thanks in advance for your help

Not mine, but cool... https://wichita.craigslist.org/snw/d/dearing-gokart/7052159345.html

I was looking for my next upgrade and contemplated porting a VC460, GX390, and/or Predator 420 head. I ended up watching a LOT of videos and took the plunge on mildly porting my VC460 head as well as installed 1.3:1 roller rockers. Off the line start it launches much harder, ~250 more RPM at WOT...

If you are ever in Kansas, this is a great place to stop by and check out. They have a lot to look at and glad we visited. http://evelknievelmuseum.com/

Question on why on the single coil only have a single wire and the two coil setup has two wires from each coil? I would have thought doubling up amperage you would have just used two single wire coils. Thanks in advance for your help Single wire...

The billet flywheel has less fan fins and lighter in weight vs. the stock flywheel. Wondering if the less fan fins could cause an overheating problem on a golf cart as well as the lighter flywheel could allow more vibrations and possibly harder to start by hand due to less flywheel weight...

Has anyone done a Comet 90d Disassemble/Re-assemble? I have the Comet 90d procedures just have not tried it yet. It would seem somewhat difficult to align the cam and the fixed face post in order to be able to install the set screw and have everything perfectly aligned. Any guidance or tips...

Thought this is pretty cool. Makes installing a 40 series a lot easier vs. jackshaft. http://rover.ebay.com/rover/1/711-53200-19255-0/1?icep_ff3=2&toolid=10001&campid=5335845805&icep_item=332553785775

Not mine https://wichita.craigslist.org/snw/d/wichita-1970s-mini-bikes/6869044115.html https://wichita.craigslist.org/snw/d/wichita-1970s-mini-bikes/6869053036.html

Not mine. https://wichita.craigslist.org/mcd/d/inman-monster-moto-212/6864108714.html

I have the following cam, springs and rockers currently in a vc460. Don't have any experience with ported heads on small engines so not sure what to expect for torque and horsepower gains. The bike the vc460 motor is installed and would run in the 2600-5500 rpm range with a tuned 40 series...

Looking for an expensive spring compressor tool for small engines like for the Predator 420. I can do it with my fingers, but the 50 lbs springs are kind of rough. Thanks