1. T

    Coleman CT200u starts then quickly stalls

    I have a Coleman CT200u. Most of the time nothing happens when i go to start it, every now and then it'll start for a few seconds then quickly die Mods made: -Governor removal -Aluminum flywheel replacement -Heavier springs installed What i've done/tested: -Cam shaft is aligned with crank...
  2. L.skynrd

    Honda 6.5hp Clone stalls out

    Hello guys. I recently bought a baja warrior of marketplace, and I am trying to get the engine running a bit better. The problem I am having, is that is stalls out at low rpms, so I constantly need to rev it in order to keep it going. It stalls mostly when I apply the brakes and come to a...
  3. B

    3100 rpm stall clutch... do i need this??

    i just bought a 212 predator engine to put on my bike and i am looking for clutches. i am seeing clutches out there that say they are 3100 rpm stall clutch. I'm not sure if it would work for me. i do know that the last one i rode with this engine was so touchy you could barely ride it so i...
  4. JoNaz

    I'm very new to the world of mini bikes

    Hi all, I'm a green rookie to this world but I'm trying to learn. I find bikes and motorcycles fascinating, but never got into them until now. I picked up a 1970 Honda CT 70H. I thought it would be a good place to start but I'm having a hard time getting started since my knowledge is basically...
  5. 125ccCrazy

    Noram Premier Titan Clutch

    New, never used, 3/4 shaft, reversible..can be run inboard or outboard.. stock stall is 4300... 14 tooth #35 chain $80 plus shipping
  6. 70sVintageTrikes

    Trike Hoarder

    Well guys im still around. It has been months since I have been on here at all. I guess the main reason is I kinda got burned out with all the crap stack of projects I have put on my plate... Everyone that knows me on here knows I was more of a buyer/hoarder than anything.. It ended up getting...
  7. J

    Help with clutch stall

    Ok so I just put a new clutch on my bike it's a max torque 14th with a black spring and I think the stall is set at 3800rpm but when I launch the bike it just Boggs but when the power band hits all you gotta do is hold on cause it flys, Does anyone know why it won't launch good Mods to the...
  8. McSpooter

    Predator 212 stall at deceleration

    Hey all, I'm pretty new to all this but still know my way around some of the stuff on these engines. I'm running the 212cc with air filter kit, 140 E tube and .036 jet, 11 inch exhaust pipe w/ muffler with the governor gear removed(stud still in place). It's had maybe 10 hours run time. My...
  9. J

    Baja Warrior 200cc Engine Idle Stall

    I have a 200cc Baja Warrior... I installed the older style ARC filter adapter and a 3/4 inch RLV muffled exhaust pipe (we run them on the race karts). I am having a problem with this engine, the carb on it is a RuXing carb, but not like the older style on the greyhound motors, it is a newer...
  10. C

    Optimal Stall speed?

    I have a briggs 3.5 on a bike right now, it's nothing fancy. All I've done is give it a quick port job, removed the gov, a straight pipe, and a free flowing air filter. The bike was setup with #41 chain, but I changed that out to #35. The only problem is, all my clutches are setup for...
  11. korndog

    Clutches, stall speed theory

    I have a cheap max torque clutch on my bike and am having some concerns about performance. I think this clutch engages at about 2500 RPM which is causing some serious bog I think. Trying to get the right balance of gearing and stall speed for optimal performance off the line and at higher...
  12. M

    Clutch stall

    What kind of stall is everyone running on their clutch setup? I just received my MT SS clutch from Max Torque yesterday. The clutch is a custom setup which also has an internal key built into the sleeve. This feature allows for quick clutch swaps and maintenance. The new stall was set to 3000...