tach

Autometer tach from my jr dragster days. Works. Has a dent in the bezzel. 50 shipped lower 48.

I am looking for a Tach to use for adjusting idle and checking max rpms. I see 2 Tiny Tachs on Ebay. One is a TT2A and the other is a TT2B. Does anybody know the difference. I cant find anything on the difference using Google. Is this what I need or should I buy a different brand/type...

There're lots of discussions on Tachometers and which one is best to use on a mini bike but, I don't recall any on how to mount one. I wound up getting a cheap one off Ebay and installed it on the handlebars temporarily using safety wire. :001_huh: I thought I'd eventually get around to...

Hi there i bought a tach for my mini bike. I hooked up the power and i know that is working. But i dont know where to hook up the signal wire. i tried the spark plug but the boot didn't go down all the way with the signal wire in the way. what should i do

Hey guys wanted to know if snyone had any experience putting a tach meant for a 4 cyl on a small engine. I've tried tiny tachs but they lag and the no backlight makes it hard to ride at night. I was thinking of finding what rpm on the tack equates to its 1 cyl rpm, and putting a new guage face...

Hey OldMiniBikes , does anyone have feedback on a good inexpensive tach they are using ? Need one for my drag bike but don't want to break the bank !! Thanks for any help:thumbsup:

I'm running 14/75 gearing with 13" tire turning 8640 RPMs on my cheap digital tach.the problem is it's only running 58.05 mph on GPS and was running 59-60 last time I was gpsing it. I have a mongrel shoe type clutch. I'm thinking about going with a disk, but don't know if my tach is just off, if...

Is there a programmable tach for any small engines out on the market? Looking to put together a 212 hemi but would like to be able to have the ability to pick the top end RPM ,like a rev limiter. I am sure they are not cheap,i have seen some nice tach's but not programmable. thanks Rick

Is it possible to hook up a tach, like a hot rod tach up to the old flat head engines like my HS40?

Digatron DT32K1 With mount (to steering wheel on race kart) and NEW leads $77 SHIPPED TO YOUR DOOR Leads alone cost this much. Thanks -GBCE

[/ATTACH] Digitron DT53 data logger. shows engine RPM, Jackshaft RPM, EGT, and CHT. has cables to download runs to a computer. shoftware is available from Digitron on-line (free). Was on our Jr. Dragster, need to get it out of the garage. would be cool on a drag bike or any other...

Looking for a hot coil for a 3hp Briggs and autometer tach for the same. Thanks

I have an old fantic motors mini bike somewhat restored with a 1989 tecumseh on it. Is there a way to install a tach on my 3.5hp tecumseh? I want to do this because it would be cool and helpful to know if you are getting full rpm. even if its not that accurate I just want it to see where it...

Here is a oldschool vibratory tachometer. It comes with Tecumseh labeled vinyl case and instructions. This item is surprisingly accurate, good shape, readout has two spots which are darker then the rest. $20 shipped anywhere in the USA. http://i818.photobucket.com/albums/zz105/5X8Rider/tach.jpg

There are numerous small engine tachs on Ebay. I would like to get one for testing my motors. What are you using and would one like ebay item 310399164033 work or is it a piece of junk. What would you use without spending big bicks. Thanks guys

Tachometer Hour meter 2 & 4 Stroke Small Engine Spark for Boat Outboard Mercury | eBay Sorry I should of put this thread on ebay

Engine is wankel sachs km3 mix 50.1, i purchase an old 2cycle 2stroke tach that i hope i can use. Now say i ended up needing one for a 4cycle would it work if i changed numbers on tach? you can see tach on handle bar. I mite of made a mistake and assumed anything that burns a mix is 2cycle, i...

Heres an oldschool analog inductive pick up tachometer, model 67-100T. Reads up to 10,000 RPM, it is in very good shape. The rubber feet on the bottom have some dryrot. Meter zeros, If there is any interest I will hook it up and verify it works. Asking $80, shipped anywhere in the lower 48...

I did a search & it looks like digital is the only real option. What one is best? It will be going on my super bronc HM100. John

Hey everyone, Newbie to the forum here. Came across your site while looking for information on modding my B&S Raptor 3 engine. I have already found a great deal of information which is awesome. Back in high school I made a mini chopper from scratch and threw on my stock Raptor 3. Lately I...