Search results

Chopper mini bike(set up like a drag bike(strait bars) This is a nice mini with a nasty look of a drag bike. 7hp, robyn Subaru ex 21 runs excellent..Plus looks spark perfect! This is a Superior engine!!! Commercial grade motor… Runs excellent.. The engine has never been altered...

Ordered a Gecker magnum machined blue printed shoe clutch,from Sheldon @ Gecker motor sports for my kart..this clutch drum and sprocket are both machined..this should be a kicker,it locks out @3700rpmm..will be here on monday...can't wait...

I have a Mikuni VM22-133 Round Slide Carburetor 22mm Carb.it is the more expensive one.I ordered pilot jets for AKG,and the OG pilot jet is shorter than the one I just bought??I got some main jets to from them the to were diff.the OG were a 8mm bolt type and the new ones are srcew in type..but...

need to drill hole for the brass pulse nipple,on the 5 hole clone valve cover.. it looks like the best spot is right in the middle of the "o" in the lettering,(there is nothing behind that area to interfear... anyone agree?disagree?

This fella hooked me up with a replacement 5 hole valve cover,and a set of stock rockers that I was in dier need of for only cost of shipping!!!.... not to mention he does not even know me.... or he probably would not have!!!HA! what a guy....thanx again JF

looking for my del.to R.I."valve cover and rockers"not sure now who it was? let me know if you see this post!did u get the check? thanx JF

I have a bone stock clone on my kids race kart (just for playing)I am leaving it that way,but was thinking that I could change the carb jet,and the em.tube,and air filter for a bit more spunk...and not much cost..the govenor is staying it's our friend!!! would it be a good thing if I put in...

lookn for a used shoe clutch max T or noram? in decent shape,higher tooth the better over 15 if I can find one? if not will settle for lower tooth....just need something to get my kart rolling to test my build...going to get the "gecker machined magnum" when I can swing it.... let me know if...

looking for input on this clone combination engine is for play kart!! new clone w/existing parts 22 mm carb open header billet fly wheel arc rod new wrist pin and c clips will the following mods make sense and work well 1.2 rockers w/laser cut giude plate 18# springs?? or do I...

I have a new greyhound,and is has the following: vs 22mm slide carb govenor,ect removed open pipe my plan is to make the following in the next few weeks.. 1.2 rockers and laser cut guide plate 18# springs advance timming 4 deg. THEN WILL add the follwing set up: arc rod,mild...

Anyone have extra of this stuff?I know can get all this from akg but there $$ 18 # springs 1.2 rockers Laser cut guide plate uni filter to fit a 22 mm slide carb mikuni main jets 120,125,130 pilot jet 12.5 let me know what ya got,Im in RI thanx JF

anyone have a 5 whole valve cover for a new type greyhound clone, they want to sell or know where to get one..I got one from t & s but is was the older 4 hole type?? thanx John

I have a Baja 50 cc,4 wheeler,the wire harness was a mess,and key was missing.so I took all the wirering harness off.and I am setting up a more simple set up..my problem is that it I cannot get spark to the plug??I get voltage from one red wire from the engine, there r 4 wires from the...

John f.357 here not been on the site 4 a long time,just got back to work from a long unemployment stretch.... Kinda gettin back into the mini and cart scene,I have also started a welding service out of my garage,so that has been taking a a lot of time. setting up.. going to the stock car...

I cut the adaptor close to the flange side,and turned it about 90 deg.this allows me to mount the carb level.it took a while,but after a few rewelds I was able to get it so it was correct.Im glad that I did not get the aluminum adaptor or I would not have been able to weld it.. The engine did...

I made the briggs adaptor fit on my clone ups just del.it @ 6:30 pm est.took a while,here's my results..I read on Bobs 4 cycle karting site,that a guy has 3 carts all set up witht e 22 mm carb on the angle,and did not have to alter the adaptor.so figured I would try it.. it fired right...

will the mikuni vm 22 mm.carb function as it should on a 15deg.angle set up for a kart Im just now putting the final touches on my clone I had to use a 15 deg.engine mount Im not sure if the carb is going to work on such an angle?? anyone know??

Me again I am trying to find out what size main,and pilot jet are in the (22 mm vm -133)carb I just got? was not able to find out from buyer,I pull the main out but did not see any numbers,and the pilot jet I could not read,but will be able to read with a mag.glass soon.. If I can find...

hey fella's time for a clutch,I have 2 in mind one a shoe and one a disk..this is not for racing just fun.. on a mild clone.. noram ultimate ge shoe=$105.00 or mdc horstman 400 disk=$115.00 any advice on which would be a better performer,and would last longer,I know about the...

I wanted u to be the first to know,I finally bought a 22mm vm-133 mikuni carb($66 new) on ebay,for the clone,not hooked up yet,got the fuel pump,lines,fuel cell,fuel pick line.all ready just need to get an adaptor(w/out pulse got it set up on the valve cover...