So i got a Hawg Ty 5.5hp mini bike toady and it looks great after some paint and tune up.
The issue I'm having is that it starts in 2-3 pulls but then once i runs even a little while and get warm it dies. Then i have to wait for it to cool down before it'll start again.
I have no idea...
I have a real Honda GX160, 5.5hp that came off some kind of pump. The guy sold it to me because the bolts in the side cover broke off. It was running fine, but he didn't want to mess with it and bought a whole new engine. I wanted the head and a few other parts, and I have no need for the...
I have a Honda GX160. The pic shows it with the aftermarket parts on but i am only selling it with the stock parts. It starts on first pull and runs great. $200 shipped to lower 48
I laughed at this guy a couple of times. He says a "frame off restoration". Frame off? really? :laugh: and then I saw the new 5.5hp briggs...BRIGGS? WTF? Its been on the MASS CL for a bit. Good Luck
Minibike
Ok, so the frame is painted, first few coats are going on fenders and "gas tank", and now I am lining up the new engine. The first thing I ran into was the 6.5 exhaust shroud was a bit high. I modified that by cutting out a section of the shroud. I rebuilt the jack shaft's bearings, and after...
I HAVE A ALMOST NEW HONDA GX160 5.5HP MOTOR ITS ONLY HAD ONE TANK OF FUEL RAN THREW IT, THE TANK THAT SITS ON THE TOP OF THE MOTOR WAS TAKEN OFF & ITS NEVER HAD FUEL IN IT. I HAVE THE TANK & ALL THE HARD WARE SO IT WILL BE MOUNTED BACK ON.
RUNS GREAT NO SMOKE, LOTS OF POWER, YOU KNOW THESE...
Hi all, first post and good to be here, had a noob question for you all.
I have searched the forums and done some research on the net but I am really stumped looking for the model number and details on this engine. My son has a black fox go cart came with a Craftsman 5.5hp I/C Briggs and...
I picked up an engine the other day from an old guy I know that does small engine repair. It's a Tecumseh Snow King 5.5 (off a snowblower) that looks almost new. I thought it would be perfect for a mini-bike but now I'm not sure because the output shaft looks like it's 7/8".
Anybody familiar...
hi i have a complete honda gx160 motor for parts, the bottom end threw the rod, lots of good parts here,
you pay the shipping from nc 28382
i think i could get flat rate box for $15.00 shipped.......
head $5.00 + shipping.... is pending
flywheel & fan wheel $5.00 + shipping
coil $5.00 +...
Yesterday while taking my son for a spin I noticed we were lacking power.
We had the bike out yesterday and she rode just fine, I rode both kids around the block a few times without issue. The only thing I did before I parked it was to put chain wax on the chain. I was careful to only spray it...
i got a GREAT running honda GX 160 NOT A CLONE!! it is on my manco streaker right now ill take it off and clean before i sell it it runs great and worked really well on the manco. it starts up on the first or second pull every single time. it will need a clutch or i will include one for extra...
ok i just got a 5.5hp honda gx160 the motor is like new and came out pressure washer is 3/4 shafth....looks good and runs good ..
never on a ''mini bike'' just use on pressure washer.........
orlando fl...140..shipped from orlando........
I am selling a tony kart go kart it is in good condition and race ready.
I just brought it in to the track near me and i paid for it to be tuned up.
This kart also comes with an extra seat that the seat cover on the seat on the cart in the picture fits on if you want a different seat...
I have a Briggs Intek 5.5HP with a bad head on it. Are these worth modding? I don't want to go that fast on it. A good top would be around 45mph, but most of my cruising time would be spent around 25-30 mph.
Also, is there any 15 degree motor mounts that bolt onto the engine plate? I need...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.