Engine turns fine, but the recoil is jammed up. I can't remove it because it has a stripped screw holding it on. Once that stripped I stopped fooling with it
Not sure on spark or compression, but all the tins and most of the throttle pieces are there. Original Tecumseh 31287 muffler is...
Here is a lovingly chromed header for the Briggs Raptor-5HP or Tec H50 engines. This has been tig welded with a RLV muffler added. This is unused, fresh from the plater! Total length is just under 11 1/2". Looking for $80 shipped lower 48
Really need a old school or repop H50 shroud serial tag. Years ago someone repop these. Hoping someone tuck one away and has now decided to never use. Willing to pay. Please pm me
Hi I purchased this NOS Tec H-50 engine about 8 months ago
.The year should be 1994 H50 65403 (B) 4088D\ 3/4" Keyed Shaft
I have too many engines and unfortunately wont be using this one any time soon
Its in the same condition unused -No oil or gas ever added-in the box as when i purchased...
I just got an h50 from another member and I've been trying to look up the model to get more info and to order parts but parts tree and jacks doesn't recognize the model number. Any help would be great. Thanks
The lighting coils are AC ... there is no battery ... will this horn work?
Saio 12 Volt AC Horn Black for Vespa VBB VBA VLB Chetak High Quality | eBay
Thanks
Kevin
This is a H50 from a Sears roper. It's got a Sears tag. Runs great. 3/4" shaft 2-1/4" long. Not throttle linkage is wrong but works. Exhaust is in great shape. Carb is newer I believe. $200 plus shipping
Exhaust tip that mounts to fender mount. Ok shape. Not rusted through. $75 plus shipping.
I have three tec h50 engines for sale at 50 dollars a piece one has one inch crank another has along 3\4 crank and the last one is a normal length 3\4 crank all need carbs.these engines run with carbs installed I am located on long Island ny and I'm really not looking to ship them I will post...
I recently found a Rupp It has a Silver H Tec motor on it. I have seen white and black but not silver. Now on the HS motors I have seen Silver Tecumseh. Can anyone confirm? This one is off a Goat.
I bought a rebuild kit for my H50 .. it included a new piston, wristpin and rings ...
Took the motor apart and the crosshatching looks great ... the old piston looks good too ...
The 2 pistons are a bit different ...
The new one is .388 shorter and weighs 7 grams less ....
The...
I recently acquired this motor. Haven't ran it, but was told it ran good when it was removed from the minibike.
Tag was removed many, many years ago. But they knew it was a 5hp.
Has great compression and spark. No muffler. Missing some of the linkage parts.
Will have this in Ann Arbor...
What is typical idle setpoint for a vintage 1980 H50 (adj. carburetor)? Minibike Service Manual indicates 1800rpm for float-type carbs. This seems extremely high. Just looking for what others have had good luck with.
Looking for the H50-H7 mini bike throttle assemble. The real deal if possible. don't mind if you pull it off any shroud that would have one.
Willing to pay as I lost out on auction. Any help?
I have a 1970 H50 ...
I bought a new stock piston, rings, gasket set and billet rod.
Any suggestions to pump it up a might ... I can shave the head, smooth the intake and exhaust ... how much can be shaved safely?
Thanks
Kevin
Complete H50,minus that funky exhaust.Going to keep that. Have not started it,but has good compression.Also has a 1 inch shaft.
Asking 150.00 Plus shipping from 73077. Numbers are H50-65363K Serial number 3162D
Haven't had an engine without a kill switch harness until now. Trying to avoid yet another task of removing the flywheel so looking to verify that this is correct connection point for the grounding switch.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.