line

Missing the Drive wheel and Sprocket.

I found this gokart on craigslist. Seller was asking $250. I offered $100, and begged for him to sell it to me. I was the very first offer and got it for $100 with the brand new engine, never run, but out of the box.

Model # and serial #. Cross referenced it as a Manco Terminator. Made sometime before 1995, brake band.

So I have this Herters sitting here. I wish I'd have been able to look it over better before buying it but am still WELL happy with it.. First drive problem is the outer rear tav sheeve. Theres a spot (melted?? :blink:) into it.. It looks like someone got it with a cutting torch or something...

cool video to watch:thumbsup:check out the guys that stand between the machines that come in and bolts a rivet head on or something:doah:little to the left or right and your getting suck in:doah: some of you guys talk about built in america. this is it:thumbsup: Fascinating 1936 Footage Of Car...

Looking for an H50 shroud that does not have any fuel line holes through the sides of it. It for a '70 H50 non electric start. I can weld mine up if needed but if someones got one:shrug: It can be bare, I have all the linkages/tag/pullstart. This lighted big block is for my Bonanza and...

1/8 fuel line?

About to mount engine. Any suggestions on how to line up the engine and clutch to the rear sprocket?

Ok, this might be a silly question....but I'm gonna ask cuz someone here will know. The clear / colored 1/4" fuel line for sale in OldMiniBikes warehouse and on eBay: Is that stuff ok with heat? I.E. Running the fuel line through the shroud like it's run on the horizontal shaft Tecumsehs? The...

Are there any Texas oil refinery workers on this board? I'm trying to figuere out what the advantage of shipping Alberta tar sands oil all the way to Texas for refining is? This is heavy high sulpher crude that needs to be run through an upgrader before its even considered refinable...

So today I got a computer generated "Birthday Card" in the mail. I opened it up and it says "Happy Birthday and Congratulations you've been selected to receive a netbook computer and 2 round trip airline tickets, absolutely FREE....please call 1-877------" I call the number and talk to a...

Using the smallest clamp I have the colored fuel line does not fit securely on the stock carb of a Baja Heat. If I tug it will come loose and I'm not liking that. It is a bit bigger ID than the stock fuel line. What do you think if I go find a smaller clamp and squeeze the hell out of it...

I have this max torque clutch http://www.affordablegokarts.com/mm5/merchant.mvc?Screen=PROD&Store_Code=A&Product_Code=SMFKC**&Category_Code=PCJ After doing some reading it seems like there are different max torque clutches. I guess the max torque that I have only stalls at 1800rpm, which could...

My Tech OHH60 6 HP (about 2 years old) does not have either and I wish to install. The engine has the stock carb and stock attached plastic fuel tank. Has anybody done this, and can you share any tips for the installation?:confused: On this engine there is not much length of exposed fuel line...

Hey all; I Put the TC2 on the mini tote The TC2 install went smoothe - however now the chain is not lining up - the TC2 torq a verter is further out then wheel sprocked - any ideas before i start trouble shooting this thinG:scooter:

What's the internal diameter of the fuel line?

This is a short video of me and my buddies trying to get my doodle bug ready 1 week before the Ventura race. I was trying to get these dual gas carbs tuned. But I end up switching to a single alky carb instead. This isn't the best quality video, it was recorded with my cell phone. YouTube...

I'm getting ready to ride a mini bike I've had for 12 years for the first time. Last night I changed the oil, replaced the spark plug, cleaned the valves, head, piston, and replaced the head gasket. I fired it up for the 1st time last night and it ran fine. I'm getting my clutch and throttle...

I'll post pics when I learn...Anyone seen a 3 wheeler that looks like a 7 foot long tote gote? 'Both' rears are driven. Appears to have had sheet metal sides or perhaps expanded metal?

I am just curious where the line is drawn when building a custom mini bike?? What I mean is, do you keep the frame and wheels pretty much traditional mini bike stuff with crazy engine mods or use a stock mini bike frame and go extreme with everything else?? What I'm getting at is that I have...