pulsa

I am looking for a Briggs carb, part number 397135. Pulsa jet adjustable carb, with choke. Thanks, Justin

Have been holding on to these cause I thought I might find a needy mini bike. Anyone know what vintage bikes actually used these pulsa jet Briggs? A purist might say none...given the color, exhaust..etc...but I just mean type engine with the pulsajet. I'm guessing the black one (3hp) is...

Does anyone know how to reattach the butterfly to the throttle linkage? As you can see, I can pull the throttle linkage out because the screw came loose inside. Ive take the carb all the way down and apart but there doesn't seem to be any access to get a screw driver inside to screw the little...

I bought a NOS Pulsa Jet carb on ebay and a fuel tank for my mower. Got it all together and found out the choke linkage cover bolt hole is not threaded , its not stripped out, just was never taped at the factory. Would anyone know what type of thread this would be. Probably will end up taking to...

Any ideas for replacing the screen filter caps on the ends of the two fuel pipes that go into the gas tank on Briggs Pulsa Jet carbs for model 80202 motors? I suspect mine are not getting clean enough and should be replaced. But a quick trip through ebay searching for the part number (296178)...

Guys....I just bought 2 new pickup tubes for my B&S Pulsa Jet Carburetor that goes on the 1976 5 hp flathead. I know that the short one just screws into the carburetor, but the longer one somehow fits over the metal tube and then uses a new ring? clamp? to hold it in place. I just tried slipping...

Does anybody have a picture of how spring on the one linkage arm on the ARC Briggs pulsa jet carb linkage kit is supposed to go :shrug: I messed around with it trying to figure it out but I couldn`t.

I've got a .750 bore raptor carb that I'm having some trouble tuning. It hesitates when I first take off but is great after I get going at full throttle. It sounds like the motor has more though. It feels like it should be getting more rpms. It's a gas carb,the metering holes have been slotted I...

well not to long ago i modded my carb alittle bit i took the bridge out and cleaned the carb for better flow where the old filter hooks up to took the choke out i also open the bore towards the coke side of the carb where it steps the bore size down by the trottle shaft and it has a shave...

Is it okay if the pull out choke on the old style Briggs pulsa jet carb for my 5hp flathead is a little loose and needs a spring to hold it in? I'm sure it's not ideal, but will it give me any problems? :shrug: I noticed that there is rivet in the bottom of the carb that holds the choke in...

Hey everyone, this is my first post so I guess I should introduce myself. I'm Evan and I have ana Azusa minibike with a 5 hp I/C. Anyways, I have the standArd downdraft pulsa jet carb. It runs awesome And everything but I have a restricted air filter selection to fit under the seat and well, and...

looking for 1 possibly 2 pulsa jet or raptor 5hp carbs, no junk... must either be in good working cond or clean and rebuildable..

Hello, I am looking for a pulsa jet carburetor for my 4hp Briggs. The current one I have cleaned and rebuilt but will not run. However when I spray starter fluid in carb it starts then dies. I have ripped it apart four times and rebuilt it so I am calling quits on that carb and looking for...

I have an elderly 3HP horizontal shaft B&S powered lawn mower which developed a problem where it would start and run for a minute or two and then stop. I found your forum had lots of really good advice and have followed it to identify that it has a pulsa jet carb which can result in this...

I just rebuilt my pulsa jet carb last night and noticed when I tore it all apart that the pick up tubes on the bottom of the carb looked like they had some kind of sealant around them where they go into the carb, it was VERY miinimal. Should I take a tiny amount of good high temp gasket sealer...

My pulsa jet had a brass throttle valve screw with a hole in the end I it calls for the silver pointed tip screw with a spring on it. You can use the brass screw but you must put a spring on it. If you do not put the spring on the screw you can thread the screw too deep and damage the...

I think......it looks like this and is mounted to the tank. Its a 5h flathead i know that. Anyone got a good used on or one that can be rebuilt? want to keep this motor stock as far as carb and tank goes. i just need the carb. thanks!

I was wondering anybody ever convert a 3 hp pulsa jet by swapping out throttle shafts on a 5hp to set up over the top 5hp aftermarket throttle kit?

does anyone know if i can swap out a pulsa jet and replace it with a vacu jet on my briggs? thanks