runs

I picked up a complete original Bird Nitehawk. Original mint seat. Hs40 that runs decent. Little smoke could pry use a set of rings. Bike has a home job paint job. Probably rattle can. It starts runs and rides. The bike is a great resto project. Located in Grandville mi. I will trade it for a...

just got a stock DB from craigs list for 150 smackers..runs and goes ,stops . I dont know what direction I'm going with it yet...any suggestions?

It did take some modification of the frame and of the back plate on the TC but now that it's done, it looks like it came from the factory this way. Like every Lifan engine I have ever dealt with, the Predator 212 runs like a top and starts on first pull. I have it bone stock. Im not really...

Santa Maria, Ca. mini bike

when i start up the engine it runs as if i was pulling it full throttle and when i twist the throttle all the way the engine idles help brand new 212 cc predator

Selling off a Bird Golden Pinto mini bike has a 5 horse Montgomery wards motor on it which runs nice i have tank drained tires etc are all nice on the bike. Thank you asking $250 or best offer located in Mankato MN

i want to know if a certain size sprocket, clutch, and wheel set up can effect the speed or how a mini bike runs ? example:big sprocket on small wheel, or a small sprocket on a big wheel or even a small sprocket on a small wheel and so on what is best and what does not so good ?:no:

The engine which died the other day did start today with a lot of smoke. Smelled like oil. Checked the oil and it's probably the original oil is my best guess from the way it looked. Changed the oil. While the oil was dripping out slooooowly as it's about 30 degrees out, I did a...

Hello, just bought a db 30 over the weekend. It starts first pull, runs very well at fast idle, however, as soon as you apply the throttle, it dies, if you quickly release the throttle, it will return to idle and continue to run. I don't see much in the way of being able to adjust the...

Motor runs just rebuilt carbs has rough idle but prob just need new plug and flywheel cleaned. Starts easy! 100$ +shipping

I jetted my stock Predator today. Used a number .037 main jet and a 140 Emulsion tube. It starts and runs but it runs very rough and seems like it's running way too rich. I switched back to the stock jets for now but how would I solve this problem? Would I have to replace the air filter and exhaust?

My faithfull Greyhound starts fine and runs great for about a minute and then stops dead. It starts right back up on usually the first pull and then quits again after about a minute. What should I check and how? Thanks for your expert advise!

I think I put it on CL for 250.. :laugh: I GOTTA get like 175 or something for it anyways... I put more time into it than I should have.. Supplied the entire throttle system and carb... Some small parts... All in all not a bad little Turd Bird... (Nobody actually knows what it is yet) It was...

I bought this for my rider but its just too big to get in my tracker. Its cool and has a new brake caliper. the carb was cleaned and tires hold air. Also has a newer belt. Its a little hard to start becuase of the pumper carb but if i show you the trick to starting it its easy! not all...

have a 97 cc predator engine . starts and idels nice , but when you get on it , seems to misfire and run rough. plug shot? carb clean out? also getting alot of clutch clatter

This is a briggs 5HP I/C it runs good , but may need carb cleaned from sitting in the garage not used.. I am asking $150 for it obo.. I am in california and prefer a local sale. Health forces sale, so I cant really ship it out. Maybe a member can help if shipping is needed.

Would be a GREAT candidate for a retso.. Kinda why I bought it, but have lost interest in them.. Plus I don't wanna throw money at it... :hammer: The GREAT....... All there.. :shrug: Original lighted Techumseh H50 runs and lights great Original seat is VERY great.. :drool: The...

Removed the head and the cylinder is scored enough that I can feel the ridges with my finger nail.Can this be honed or will I need to have it bored out?

my dad got his ram to pop right off but still the twist grip barely wants to turn and she moves like a turtle.....u use the linkage by hand to accelerate and its fine....any tips? gotta bad spring?

I messed up and put some runs in my paint today. I'm still gonna spray some duplicolor clear effex on it. It has a metal flake in it. After I do that I'm gonna spray some auto quality clear on it with my HVLP gun. I was just wondering if I can wetsand the runs out before these steps. Thanks!