h30

Hello All, I need some help and advice from the masters on this page. While I am not a novice when it comes to small engines, this is the most in depth I have gone working on one. Here is what's up: I got this 70s ARCO E-Z Rider from my mother in law 13-ish years ago. It is a H30 -35176J -...

I got a Bug go kart with a Tecumseh H30 that I can't get to idle. I have a few questions about getting it to work. Wich way does the diaphragm go? Does the diaphragm go against the carb then the gasket followed by the cover plate? My carb says F3 by the air filter and then says H where the carb...

anyone know if the Governor wheel and mechanism is the same on a h30 and hs40. im rebuilding an hs40 and the govner is all removed, i have a knocking h30 and i want to pillage the parts from it if its compatible.

Tecumseh H30 with 3/4" keyed shaft. Starts about 3 pulls and runs good. $85 buyer pays for shipping. Yes it came of a low hour snowblower. If that bothers you I can set it on a Trail Horse frame for 60 seconds and then you can tell your friends it came from a vintage bike. :laugh...

Think it's a 80's h30 side popper. Cleaned it up and replaced gaskets. Painted it with VHT hi temp paint on the block. Installed 3hp decal set. Custom side popper header and new carb. Engine runs. Will need carb adjustments once installed on bike. Includes custom rock deflector in place of air...

Iso tecumseh h30 or 35 preferably with a lighting coil. I need one with the exhaust by the intake not a side popper. Thanks

I got this Cyclops survivor back in the summer and finally started trying to get her going. I had high hopes that I might get the engine running without a lot of fixing but had that idea blew up almost immediately. I drained and changed the oil without any problems. Then I put gas in the tank...

Hey everybody, First 56yr old newbie question regarding flywheel key problem that I cannot figure out:anon.sml: I had a spark problem on my H30 that required me to pull the flywheel to investigate. I traced it to a cut condenser wire that I fixed, but when I put everything back together, I...

This is the motor I was just trying to get the Fairbanks Morse clutch off the PTO. I was going to just use it for parts after selling the clutch but I couldn't sleep the other night and decided to time it mainly out of boredom. I was amazed at how clean it looked when I took the shroud and...

Trying to find out what year this Tec is. H30 35319M Thanks

I need a replacement carb for my H 30 engine. The one I have is shot, any suggestions on a good replacement and where to get it? Thanks

Hey guys. Just picked up this little H30 side popper off eBay. It's got a keyed 5/8" shaft and a diaphragm carb on the long skinny intake. I want to retrofit this engine to make it minibike-compatible. I know I need the cable-type throttle control at the very least, but ideally I...

Here is my latest edition to my collection. I'm pretty sure it's a Speedway Shrike. Not sure in the year though. Any help or pointers what you see would be appreciated. It has an H30 Tec on it. It's missing the original exhaust and the back fender is missing the back half. This is going to be a...

Looking for a White Air Filter assembly for a Tecumseh H30 Engine.

So the ARCO H30 I picked up last weekend has no compression. I opened the head and poured oil inside and it fairly quickly got by the piston and into the sump. Pretty safe to say that this is the cause no? Bad piston rings? Ive never changed em. Anyone have or know of a decently simply step...

Found this complete H30 from an ARCO today. H30 35260H 1971. Even all the minibike throttle linkages are there and connected. All silver this time.. No spark or compression. Not stuck at least. Havent opened it yet but hopefully its nothing major. Looks like the original carb too...

Tecumseh H35 flywheel. Part number 31332. May fit other models as well. $35 shipped - lower 48 states only. Located near Detroit, MI 48088. Discount given if you can pick up and pay cash.

Hard to find Tecumseh "Mini-Bike" specific throttle. These were reproduced by OldMiniBikes memeber Joe51 a couple years ago. This is the small block version which I believe fits all H25, H30, H35, HS40 and HS50 engines. The attention to detail on these is superb. These were manufactured exactly the...

Nice aluminum Techumseh flywheel....magnets test strong..... taper bore is nice as are all the fins. $35 shipped.... (There's a guy on Ebay now asking $45 plus $60 to ship :doah:)

H30 Carb