jet

  1. Dirtnap

    Questions About the Coleman CT200U Carb and Parts,...

    What's up fellas, I have me a CT200 ordered and tracking showed it shipped today, curious if any of you guys know if this has the 200 Honda clone motor? I've been looking on OldMiniBikes Warehouse's site and hoping to get the jet kit with intake and a filter, hoping to find a UNI foam filter that will...
  2. brendanp

    predator 212 OMFG!!

    So anyway, its been a while since i have been on here. I just finally finished up my 212 install. I have to thank all you guys for the help I got. also, some guys sent me free parts. But I got to take it for a lil spin today, and OMG. That this is pretty damn fast! It was pulling wheelies...
  3. delray

    mikuni carb ID

    Pick up this mikuni carb that i want to run a clone engine,but i am not sure what type i have. I thought it just had the small brass hex main jets. After taking the bowl off i notes it has a large style jet with tube and o-ring. What type is this and where can i find that type of jet. Right now...
  4. D

    Briggs 6.5 vertical shaft

    Okay, I'm stumped. It's not for a mini, but I know you guys can help. I've got spark. It will run when I prime it (or on starting fluid), but it dies shortly after. I have cleaned the carb vigorously two times. There is no leak between the carb and block, and I know the main jet is clean because...
  5. D

    mikuni 22mm needle jet clip

    I was adjusting my needle jet clip and it flew off. I can't find one that's for my Japanese mikuni 22mm, I think it's a vm22. Anyone know where I can. Get the right clip at? Thanks
  6. T

    Governor Stop Screw DB30

    Does anyone know where I can get a Governor stop screw for the stock engine? I searched and could not find it. I just picked up one of these for cheap and I want to be able to restrict the top speed, but the screw is missing. I am going to get the Jackshaft from Pro Mod and otherwise keep...
  7. R

    pred 420

    re jet eng & now exhausting out intake......any advice ?
  8. D

    new parts = no start

    Removed governor 18lb. Springs Air Filter Exhaust 1" Timing key 6 degree Emulsion tube 140 + 37 jet No start choked/non-choked.... Occasional blue flame out exhaust n carb.. Swapped back stock emulsion & jet got more blue flames out of carb n exhaust.. I may have failed on setting...
  9. la1

    VERT B&S 9ci mower question about a Pulsa Jet

    I bought a NOS Pulsa Jet carb on ebay and a fuel tank for my mower. Got it all together and found out the choke linkage cover bolt hole is not threaded , its not stripped out, just was never taped at the factory. Would anyone know what type of thread this would be. Probably will end up taking to...
  10. gomurray2track

    Preadtor 212 dies when throttled up

    Hey Guys, I'm at a lost with this motor. Could really use some help. I have a brand new 212, header, air filter kit, and 037 jet, and 140 e tube installed. It starts fine but runs at a high idle and when i give it a little throttle it dies. I've try cleaning the carb, using the 036 jet. nothing...
  11. S

    Honda GX270 jet size

    Anyone know what I should jet the GX270 carb to? Or should I just buy a 390 carb and call it a day. I haven't done any engine work other than header and intake.
  12. YOOP

    trail jet

    1971 TRAIL JET MINI BIKE
  13. T

    Tuning a mikuni 22mm carb

    I can't seem to get my bike to idle . It just runs at high RPMs . Adjusting the fuel/air still can't bring it down .is this a jet issue ? I don't know what size jets it came with. Any help would be appreciated .
  14. brettdn

    Jet Size needed for a very mild GX160

    I recently installed OldMiniBikes's 8 inch header and angled air filter on my GX160, I already have a 140 emulsion tube and a .36 jet installed and the motor runs fine but the spark plug is really black and I am assuming it is running rich, this was both tested on a NGK BRP6ES and an Autolite AR3910X...
  15. george3

    DB-30 97cc

    I need a main jet for a DB-30 97cc Someone drilled the jet out way too big and it just floods out. Does anyone have one they can part with?
  16. B

    Wanted Briggs and Stratton 3 or 4 hp

    Horizontal 3/4" shaft flow jet carb running condition
  17. HueyLewis

    Honda GX120 Carb HELP!!!!!

    Hello, I am having trouble getting my GX120 to idle and it seems to be getting choked out at WOT. I had to replace the carb and the most readily available one for me was for a GX160/GX200. it has the stock jet in it but I assume it is the stock jet for a 160. has anyone had success with a setup...
  18. D

    Help on jetting issue

    Hello everyone, this is my first post.. I recently built a 212 Predator with the Hemi head and need some help tuning Here is what I did to the build- Removed the govoner Removed the low oil Spenser Installed air filter and adapter Minibike header 18lb valve springs Racing spark...
  19. terra jet

    terra jet

  20. terra jet

    terra jet

Top