kohler

My manco thunderbird pulls the front tire off the ground. I love this new engine! How can I make sure that I'm getting everything out of the engines powerband! My linkage pulls the carb all the way open.

2 stroke Kohler

So I have parts of a Kohler engine, my dad thinks its a 6-7hp. Unfortunately, it is missing some key parts... like the innards... very key if you ask me! Here is some pictures. I do have a few more pictures. I would like to know if it would be worth trying to get parts to get it running? As...

Nice running Kohler K91 as shown. Will ship it from 49221. It runs good with no smoke. It currently has a rare lighting pull start installed on it to power lights. $200+ship without the lighting pull start / $275 + ship with the lighting pull start. The stock recoil is fine just needs new rope...

dont know if this is the right place to post this? but thought it was similar to the honda's and clones.Was wondering if anyone has ever used these engines and if they are capable of using honda parts for mods? and if u can mod it? i posted a link to show the engine let me know your thoughts...

Hello, I recently acquired two Alsports. One is a 339cc Kohler. The engine is model number SK3402AS. Serial number on the neck is 1 25747. I assume it's a 74? Anyone with advice on how the vin decodes would be greatly appreciated. Thanks.

Posted in wrong place and can't figure out how to delete. I'm sorry:facepalm: Hello- The rules say to post things seperately in "What is it?", so here goes. I DO have two in case you saw my other post. The second is an Alsport Trisport with 339cc Kohler engine. It has Kohler engine model...

Posted to wrong place. Sorry Hello- This is my first post here. I have acquired an Alsport with 440cc engine. I am not sure if it is Kohler engine? It has a Maple Leaf and the letters CCW stamped on the motor case. The neck has serial number 073078 stamped on it. Is that a 73 or a 78...

I have a Ward's trike with a Kohler 295 cc 2-stroke in need of gasket replacement. Does anyone know torque specs for this

Anyone use the Courage line of engines from Kohler? I did a search and didn't find much....

Listing for a friend / All engines run good and ready to bolt on: 1. Kohler K-161-T Spec#28937E Ser# 749283 7 HP 1 inch crankshaft, screw in dipstick, recoil start. ($250) 2. Clinton Model 1200-2126 Ser#4416980B ($280) This is the list of work done: Engine was dismantled, cleaned...

just checking to see if any one needed this old cast iron kohler motor i think its a 5hp.. or if any one needs it or any parts ill get pictures on here..

I should stop buying shit

Hello, I am new to the site but I Love reading all the posts of everyone bringing these toys back to life. As for mine, yes I 'm a woman & this has been my very 1st engine to work on. My husband has been guiding me through the process & I can't get enough.,...Just yesterday, I dropped off the...

WOW :drool: Found a Kohler 18 horse Magnum HORIZONTAL crank at the junkyard today... :drool: And it looked like TOTAL crap, so I tore the heads off and a LOT of rusty water poured out of each.. :ohmy: But the walls wiped clean pretty well, and both rods are unbroken.. :deal: So I carry the...

What is the hp 0f a 296 cc kohler and is it a 2 or 4 stroke? Will it fit on a dunecycle in place of the 5 hp briggs? Thanks.

Has anybody tried using a big 20hp+ kohler in their karts, mini bikes? Becasue I don't know haw they would run in a bike since they have a cast iron block, and also what kinda clutch would you use? :sailor:

Could anyone offer any "how to" help and/or suggestions for hooking up a throttle on a 6hp Kohler Command (slant cylinder design) CH6t-15102 engine? I recently purchased the engine unused and very cheap for a minibike project for my sons (and me too of course)! Any help would be appreciated...

I just finished this up! Well almost finished...stil waiting on the carb to come in! Its a 1964 Kohler K181 off a John Deere 110! Was sitting an a crate in an old shed for about 25 years! What do ya think...

i do not know the size or horsepower. maybe someone will recognize it and let us know. it looks to be army issue. does run. looks to be 5/8 shaft, asking $60 shipped. located in so cal.