advise

I have a bare frame,fork, and motor. The goal is to have a cheap mini to ride with my grandson. The question is; What would be the cheapest way to get all the parts to build a mini bike? I would like 8" wheels but I will go 6" if I have to. Azusa part kit? gather individual parts. Any bargains...

First time posting on this forum. I am a volunteer for a 501c3 non-profit. A group of folks are working on a Ken Bar Whirlwind with an original H40 engine. The aluminum cylinder walls are scored beyond repair from possible cracked ring(s). The crankcase/valve guide breather is expelling...

Hey All, My little H25 or H30 tec (I have no idea which..:laugh:) has been apart and out of service for way too long now and i'm getting tired of kicking it around the shed. I need to put her back together! It's got the standard bore size for an H25 or H30 (they share the same bore) and it...

My 1969 Rupp Roadster is all original and when purchased a year ago it had a slipping in the clutch when it transitioned from 1st to 2nd gear. I dissembled the jack shaft and replaced the Sprag gear and it ran perfect. Stong shift from 1st to 2nd. Now after a year it is doing it again. Can it...

Is this '59 sportin anything that doesnt belong here aside for the engine of course?. What abt that seat? Is it missing anything id have a hell of a time finding? Ive been wanting to break into the world of Tote Goting for awhile. Would this be a good start? Its going for cheap as far...

I find myself in need of some advise for an engine, as I'm a bit behind the 8-ball on small engineas. Have a Briggs 3-hp flathead off of an older Sears lawn edger. Numbers are 143 814032 SER 0317B. Missing carb and tank. (It looks like the carb would have been mounted to the bottom of the...

I have the chance to pick up this,what the guy says ,is a Speedway Scorpion for 100 bucks.It has its issues,like the engine plate has been cut and rewelded flat(not done very well from what I can tell and one of the shocks appears bent not to mention it seems to be missing some parts most...

Here I go again. I had hoped this day would never come but I was looking around craigslist this morning and found a bike I think is probably worth the money. Maybe I'll start another project... The seller claims it was bought new and has been stored for the last 6 years. No other info, yet...

Doctors here are the symtoms runs ok for awhile runs a little faster stalls no fuel visible in filter choke the mess out of her and she pulls gas up enough to see in filter finally starts runs ok for awhile runs a little faster stalls no fuel visible in filter Two options I can...

HI, guys i have a chance to buy a vintage Tecumseh 4hp mini bike engine it's has great compression for 25.00 bucks . Here the problem it's only the block , no carburtor , no muffler , no gas tank. The block look's great my question is would it be worth it to buy it and replace the missing parts...

HI, guys i notice a few holes in this frame, they look like somebody drill them there but i'm not sure. There one on each side of the frame between the two seat brackets ,might be hard to see it in the picture the other is by the rear wheel. My question is if they are orig to the frame what...

We are looking for a good camp grill / griddle / stove and want to know what others use. I'd like a small to medium sized grill / griddle area with one stove burner on the side. I keep seeing this "Camp Chef Rainier" and "texsport" and "coleman" setups. Does anyone have any experience...

hay guys my dad and i and i'm 17 have been working on a Retek cheetah here all winter found a 5hp motor off a snow blower to fit it because all i had was wheels ,seat, and the frame i got a head light and handle bars off a three wheeler now i,m working on trying to figure out how to do a brake...

I am about to wrap up my Honda FL250 restoration and will be looking for a kart to build. I don't want to waste anyone's time so I will just tell you... Here is what I want to do... Find a kart (superstore) where I can see what is available first, Find a solid frame to work with, Build more...

I am about to wrap up my Honda FL250 restoration and will be looking for a kart to build. I don't want to waste anyone's time so I will just tell you... Here is what I want to do... Find a kart (superstore) where I can see what is available first, Find a solid frame to work with, Build more...

1" gas Tilly with choke $37.00 Tillotson HL-232 Carburetor - eBay (item 320549274242 end time Jul-15-10 23:00:33 PDT)

Need help from you experts out there Please. I picked up this chopper frame and I am trying to figure out a rear wheel/tire/brake combo. The width measurement at the rear axle holes is 9inches. Handle bar ideas too. Any and all ideas Greatly appreciated! Prefer used stuff Thanks JB